Bosch Appliances MIC400AL operation manual Installation Instructions

Page 26

MIC400 Series Camera Installation and Operation Manual

Installation Instructions

WARNING: Electrical Danger: Ensure all power is disconnected before opening or working upon any Power Supply Unit.

Installation must be carried out by suitably qualified persons & all local safety regulations should be followed. After removal of the lid take care as components can reach a temperature of 55 Deg C.

CAUTION: It is extremely important to observe the correct polarity, failure to do so will result in the destruction of the DC-DC power supply.

CAUTION: This power supply was designed for negative earthed vehicles only it is not suitable for use with positive earth vehicles.

To install the MIC-IR-12PSU please do the following:-

1.Locate the mounting position of the MIC-PSU so that it cannot be interfered with either intentionally or accidentally, a lockable cabinet or secured vehicle location i.e. a lock box or mount rack is recommended.

2.Securely fix the MIC-PSU using M4 stainless steel screws & washers; ensure the cable glands have sufficient room to allow for the cables to enter.

3.Feed all cabling through the appropriate sized gland holes.

4.Connect the composite cable to HD3 following the colour coding as shown in the Table B & printed on the PCB, connect all wires.

5.Connect the Brown and Grey wires for the IR lamps to HD6 as per Table J

6.Connect the Coaxial video cable to the CN1 header.

EN 26

7.If alarms are to be used connect these to HD2 as per Table I above.

8.Telemetry connections are provided by headers HD4 and HD5 which respectively enable crimp or screw terminations for connecting the MIC400 to the control equipment.

9.Connect the power to HD1 carefully observing the polarity and voltage as per Table A.

10.A washer drive is provided on this power supply, a mains rated relay is fitted and pre-wired to the mains input feed via an on board fuse FS4 (rated at 2 Amps Ceramic quick blow); connection to a third party washer pump system should be made via HD7 as per Table K.

11.Once connected the washer drive can be tested using the red SW1 which should activate the pump. When pressed the LED, (LED3) next to the washer switch should illuminate. The LED will also illuminate in response to telemetry commands to switch the washer on. The Red LED on the washer PCB will illuminate when the Washer function is selected at the control room end. Note that the software in the camera prevents the washer from being run more than 10 seconds continuously. (This is to prevent the washer bottle from being inadvertently emptied. The red button on the washer drive card can be used to both test the washer operation and to prime the washer pump.

12.When wiring is complete, apply power & check the all six (6) LED’s are lit.

13.LED1 and LED2 when light show that 15v AC is available from the power supply (i.e. the supply fuses are intact. There is no indication of the operation of the Telemetry lines as this would increase the load on these lines reducing the number of cameras that can be driven by a single telemetry spur.

14.LED 3 illuminates when the washer drive relay is selected to on.

15.LED 4 monitors the internally generated +5v rail used to drive the alarm interface circuits around HD2. This +5v supply is not available externally.

Bosch Security Systems

Issue 1

Page 25 Page 27
Image 26
Page 25 Page 27
Contents MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-24PSU MIC-240PSUMIC-115PSU MIC-12PSUMIC-BP3 MIC-WKTMIC-ALM MIC-BP4Packaging Contents UnpackingInstallation Environment Key to MIC-PMB drawing Associated Equipment & Typical Installations Installation InstructionsLightning Protection Underwater InstallationEarthing of the MIC400 camera Table a MIC Composite Cable Pin table NON-IR Power Supply UnitsElectrical Connections MIC-240PSU, MIC-24PSU and MIC-115 PSUPCB Earth Link Power Supply Layout and ConnectionsTable B Power Connection to Header HD1 HD5 HD3HD4 Bi-phase cards etc Rating for Primary12 or 24 Volt vehicle supply MIC-12PSU Power Supply UnitTable G Power Input wiring connections for MIC-12PSU MIC400PA Optional Cards and Kits for Non-IR MIC400 CamerasCommissioning MIC400PA and MIC400’s with heaters fitted Heater OptionBosch Security Systems Issue MIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU MIC400IR Power Supply UnitsSetting the Power Supply Link Options Figure D MIC-IR-240PSU Layout Table I Fuse Ratings for MIC-IR-240PSU Function TypeTerminal Box ID Marking SignalTable K -IR Lamp Connections HD6 Table L -Washer Pump Connection HD7MIC-IR-12PSU Figure E MIC-IR-12PSU Schematic Table M Fuse ratings for MIC-IR-12PSU Function Type RatingInstallation Instructions Table N Connecting the Greenwich Adaptor Connecting the MIC400 to the PCConnecting the Greenwich Adaptor Adaptor ConnectionsSetting Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorDIP Switch Table O K2-ADE Adaptor connectionsCommunication Mode Table Q MIC-USB485CVTR Connection Table and DiagramMIC Power Supply Converter Output Telemetry Header Standard Controls MIC-USB485CVTR and Universal Camset Software InstallationCommissioning the MIC400 through Universal Camset Boot Messages MIC SettingsCamset Settings Iris Controls Reset CamsetManual Control Pan, Tilt and Zoom Controls Focus ControlsPreset Positions AuxiliariesTour Controls Soft Stops and Non Dwell ZonesPan Reverse MIC SetupsGeneral Settings Tilt ReverseAuto Home Controls Default Settings Other controlsMulti Alarm Settings Lens Recalibration and Frame Integration Frame Integration SettingsPrivacy and Captions Privacy Controls Privacy Calibration CaptionsThermal Timers Advanced SettingsTemperature and Humidity Clear All StatisticsUpload Eeprom From File Eeprom CopierDownload Eeprom To File Remap Auxiliary Pelco OnlyMatrix Controls POT TestMenu Controls Panasonic Only Pot Test Controls Pot Test ResultsSend Direct Command CommsMIC Comms Communications TestingAlarms Cam CommsSend Preset to MIC SonySet Preset NumberGet Preset from MIC Sony SetSave Table from MIC to File Execute this PresetLoad Table from File to MIC Clear TableTable R Sonyset Commands MIC Programmer Bosch Security Systems Issue Operational AlarmsCamera Module Communication & ProtocolsEnvironmental AccessoriesPhysical ElectricalMIC400PA Twin SpeakersMIC400UL and MIC400UT MIC400S MIC400IR IR IlluminatorsDimension Drawings Asia-Pacific Contact AmericasEurope, Middle East, Africa Bosch Security Systems IncPelco Appendix a Protocol Preset codesPreset Codes Bosch Security Systems Special Setup Presets VisionBosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2
Top Page Image Contents