Bosch Appliances MIC400AL Optional Cards and Kits for Non-IR MIC400 Cameras, MIC400PA

Page 19

MIC400 Series Camera Installation and Operation Manual

EN 19

Optional Cards and Kits for Non-IR MIC400 Cameras

The MIC400 has several optional cards and kits as described earlier.

Please refer to the respective manuals for details on their installation and operation.

MIC-WKTWasher bracket, nozzle and pump card kit for non-ir cameras

MIC-ALM8-input alarm card for non-ir cameras, includes washer pump drive function

MIC-BP3Bosch Bi-phase converter card for MIC-power supplies without an expansion slot available including all IR psu’s

MIC-BP4Bosch Bi-phase converter card for MIC power supplies with an available expansion slot.

Commissioning MIC400PA and MIC400’s with heaters fitted.

MIC400PA

The MIC400PA has two (2) 6w, 8ohm, IP67 rated speakers connected in series to allow for public address applications, these utilise the Brown and Grey wires on the composite cable that are normally used for IR illuminators.

There are no connections for speakers on the power supply itself; the speakers are connected directly to a third party amplifier and microphone.

To utilise the speakers please do the following:-

1.Disconnect the power supply from the power source; locate the Brown and Grey wires in the composite cable.

2.Using a terminal block connect the Brown and Grey wires from the speakers.

3.Feed the speaker cable through one of the conduit glands in the PSU enclosure.

4.Connect the speaker cable from a third party amplifier and microphone to permit the speakers to be used.

Heater Option

Applicable to the following power supplies only.

MIC-240PSU, MIC-115PSU, MIC-24PSU and MIC-12PSU only.

There are two links on the power supply printed circuit board which must be changed to allow heater operation. Please do the following to enable the heaters to function:-

1.Disconnect the power supply from the power source; locate the Brown and Grey wires from the composite cable.

2.Locate the PCB links next to HD6, the default setting is 0V (shown below)

Bosch Security Systems

Issue 1

Image 19
Contents MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-12PSU MIC-240PSUMIC-115PSU MIC-24PSUMIC-BP4 MIC-WKTMIC-ALM MIC-BP3Unpacking Packaging ContentsInstallation Environment Key to MIC-PMB drawing Installation Instructions Associated Equipment & Typical InstallationsEarthing of the MIC400 camera Underwater InstallationLightning Protection MIC-240PSU, MIC-24PSU and MIC-115 PSU NON-IR Power Supply UnitsElectrical Connections Table a MIC Composite Cable Pin tableTable B Power Connection to Header HD1 Power Supply Layout and ConnectionsPCB Earth Link HD4 HD3HD5 Rating for Primary Bi-phase cards etcTable G Power Input wiring connections for MIC-12PSU MIC-12PSU Power Supply Unit12 or 24 Volt vehicle supply Heater Option Optional Cards and Kits for Non-IR MIC400 CamerasCommissioning MIC400PA and MIC400’s with heaters fitted MIC400PABosch Security Systems Issue Setting the Power Supply Link Options MIC400IR Power Supply UnitsMIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU Table I Fuse Ratings for MIC-IR-240PSU Function Type Figure D MIC-IR-240PSU LayoutTable L -Washer Pump Connection HD7 SignalTable K -IR Lamp Connections HD6 Terminal Box ID MarkingMIC-IR-12PSU Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Figure E MIC-IR-12PSU SchematicInstallation Instructions Adaptor Connections Connecting the MIC400 to the PCConnecting the Greenwich Adaptor Table N Connecting the Greenwich AdaptorTable O K2-ADE Adaptor connections Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorDIP Switch SettingMIC Power Supply Converter Output Telemetry Header Table Q MIC-USB485CVTR Connection Table and DiagramCommunication Mode Commissioning the MIC400 through Universal Camset MIC-USB485CVTR and Universal Camset Software InstallationStandard Controls MIC Settings Boot MessagesCamset Settings Focus Controls Reset CamsetManual Control Pan, Tilt and Zoom Controls Iris ControlsAuxiliaries Preset PositionsSoft Stops and Non Dwell Zones Tour ControlsTilt Reverse MIC SetupsGeneral Settings Pan ReverseAuto Home Controls Other controls Default SettingsMulti Alarm Settings Privacy and Captions Frame Integration SettingsLens Recalibration and Frame Integration Privacy Controls Captions Privacy CalibrationThermal Clear All Statistics Advanced SettingsTemperature and Humidity TimersRemap Auxiliary Pelco Only Eeprom CopierDownload Eeprom To File Upload Eeprom From FileMenu Controls Panasonic Only POT TestMatrix Controls Pot Test Results Pot Test ControlsComms Send Direct CommandCam Comms Communications TestingAlarms MIC CommsSony Set SonySet Preset NumberGet Preset from MIC Send Preset to MICClear Table Execute this PresetLoad Table from File to MIC Save Table from MIC to FileTable R Sonyset Commands MIC Programmer Bosch Security Systems Issue Communication & Protocols AlarmsCamera Module OperationalElectrical AccessoriesPhysical EnvironmentalTwin Speakers MIC400PAMIC400UL and MIC400UT MIC400S IR Illuminators MIC400IRDimension Drawings Bosch Security Systems Inc Contact AmericasEurope, Middle East, Africa Asia-PacificPreset Codes Appendix a Protocol Preset codesPelco Bosch Security Systems Vision Special Setup PresetsBosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2