Directed Audio XTR2502, XTR5002 owner manual Symptom Probable Cause

Page 19

Symptom Probable Cause

Action To Take

Speaker not connected to amplifier properly..

Check speaker wires and repair or replace as needed.. Refer to the Speaker Connections section of this manual for detailed instructions

Internal crossover not set properly for speakers	Readjust crossovers.. Refer to the Internal Crossover Configuration section of
	this manual for detailed instructions..

Speakers are blown	Check system with known working speakers and fix or replace as needed..

Poor bass response

Speakers wired with wrong polarity causing can-	Check speaker polarity and fix as needed..
cellation at low frequencies..

Crossover set incorrectly	Reset crossovers.. Refer to the Internal Crossover Configuration section of
	this manual for detailed instructions..

Impedance load at amplifier is too low..	Check speaker impedance load if below 2Ω, rewire speakers to achieve
	higher impedance ..

Battery fuse blowing

Short in power wire or incorrect wiring..	Check power wires and ground connections and repair or replace as needed..

Fuse used is smaller than recommended..	Replace with proper fuse size..

Actual current exceeds fuse rating..	Check speaker impedance load if below 2Ω, rewire speakers to achieve
	higher impedance ..

Speaker is blown with shorted outputs	Check system with known working speakers and fix or replace as needed..

© 2008 Directed Electronics. All rights reserved.

18

Image 19

Contents Amplifier Contents Introduction Low bass frequencies below the range of human hearing, that Over Frequency Control Flat / All Pass output- adjustsPass, or HPF high pass crossover Speakers Right channelCEA Specifications Specifications Crossover Switch Signal Input and Output ConfigurationsLine Output Configurations Internal Crossover Configurations, Flat full rangeHigh-Pass Crossover Adjusting Bass Boost XTR 5002 onlyInfinite Baffle Subsonic is set at 20Hz Sealed Example High-Pass Set at 30Hz Sealed Example High-Pass Set at 20HzSpeaker Connections XTR2502 and XTR5002 Power ConnectionsBridge Configuration Trunk Compartment General Precautions and Installation TipsChoosing Mounting Locations Passenger CompartmentTools of the Trade Step By Step Installation Adjusting the Sound of the System Testing the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Symptom Probable Cause Action To Take Troubleshooting TipsSymptom Probable Cause Réglage de fréquence X-OVER sortie passe-tout / neutre Disposition DES Panneaux LatérauxCEA Specifications Caractéristiques Techniques Réglages DE L’AMPLIFICATEUR Réglage passe-haut à 20 Hz dans le cas d’un cais- son clos Filtre passe-basFiltre passe-haut Réglage du renforcement des graves XTR 5002 uniquementRéglage passe-haut à 30 Hz dans le cas d’un cais- son clos Raccordement DE L’AMPLIFICATEURRaccordement de l’alimentation Trois canaux canal 1, canal 2, pontés Configuration un canal/deux canauxRaccordement des haut-parleurs pour XTR 2502 et XTR PontageHabitacle Installation DE L’AMPLIFICATEURChoix des emplacements de montage Précautions générales et conseils d’installationOutillage requis Installation pas à pas Essai du système Réglage ET Résolution DES ProblèmesRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Symptôme Cause probable Intervention Conseils de dépannageFrançais Symptôme Cause probable Disposiciones DEL Panel DE Extremo EspañolTHD+N Especificaciones DE LA CEAEspecificaciones Configuraciones DEL Amplificador Bafle infinito, filtro subsónico en 20 Hz Crossover de pasabajasCrossover de pasaaltas Ajuste del refuerzo de bajos sólo XTR5002Conexiones de altavoces del XTR2502 y del XTR5002 Configuración de un canal y dos canalesConfiguración en puente Cableado DEL AmplificadorEspañol Maletero Instalación DEL AmplificadorSelección de ubicaciones de montaje Compartimiento de pasajerosHerramientas DEL Oficio Instalación paso a paso Prueba del sistema Configuración Y Detección Y Reparación DE AveríasDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Síntoma Causa probable Medidas a tomar Sugerencias de detección y reparación de averíasEspañol Síntoma Causa probable Layout DER Endplatten DeutschCEA-DATEN Technische Daten Verstärkereinstellungen Unendliche Schallwand, Subsonic auf 20 Hz einges- tellt Tiefpass-CrossoverHochpass-Crossover Einstellung des Bass-Boost nur beim XTR5002Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 Hz Verstärkerverkabelung Fahrgastraum VerstärkerinstallationAllgemeine Vorsichts- und Installationshinweise Wahl der EinbaustelleWerkzeuge Schrittweise Installation Systemtest Einstellung UND ProblemlösungSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Symptom Mögliche Ursache Lösung ProblemlösungenLösung Symptom Mögliche UrsacheDirected Electronics. Alle Rechte vorbehalten Layout DEI Pannelli Terminali ItalianoSpecifiche CEA Dati Tecnici Guadagno d’ingresso Configurazione dei segnali d’ingresso e di uscitaConfigurazioni delle uscite di linea Impostazioni DELL’AMPLIFICATORECrossover passa-alto Crossover passa-bassoRegolazione dell’amplificazione dei bassi solo per l’XTR Connessioni per l’alimentazione Cablaggio DELL’AMPLIFICATORETre canali canale 1, canale 2, cablaggio in paral- lelo Configurazione a uno o a due canaliConfigurazione a cablaggio in parallelo Connessioni degli altoparlanti XTR2502 e XTR5002Abitacolo Scelta del punto di installazionePrecauzioni generali e suggerimenti per l’installazione Nstallazione DELL’AMPLIFICATORECorredo per l’installazione Procedura di installazione Prova dell’impianto Impostazione E Soluzione DEI ProblemiRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Sintomo Causa probabile Intervento necessario Soluzione dei problemiItaliano Sintomo Causa probabile Layouts DOS Painéis PortuguêsEspecificações DA CEA Especificações Ajustes do Amplificador Exemplo de caixa selada com passa-alta ajustado a 20 Hz Crossover passa-altaAjuste da intensificação de graves apenas XTR5002 Sonoflector subsônico infinito é ajustado a 20 HzConexões elétricas Conexão DOS Cabos do AmplificadorTrês canais canal 1, canal 2, em ponte Configuração de um canal/dois canaisConfiguração em ponte Conexões dos alto-falantes XTR2502 e XTR5002Porta-malas Instalação do AmplificadorEscolha de locais de instalação Cabine de passageirosFerramentas Instalação passo a passo Como testar o sistema Ajuste E Resolução DE ProblemasComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Problema Provável causa Medida a ser tomada Sugestões para resolução de problemasInterno deste manual Problema Provável causa Medida a ser tomada Warranty