Pelco cs73m-d operation manual Pelco Manual C573M-D 11/03

Page 37

7.Set the message text format characteristics in the lower right-hand corner of the Message Text Editing dialog box by programming the following information:

¥FormatÑSpecifies the positioning of title/time/date text and message text. Select the desired setting in the list box using the up or down button:

ÐTitles on Top specifies that title/time/date text is to be positioned above message text (default setting).

ÐMessages on Top specifies that message text is to be positioned above title/ time/date text.

¥Rows to DisplayÑSpecifies the number of rows (lines) of message text to be displayed. In addition, the Rows to Display field also specifies the number of rows of text that can be scrolled (for information about scrolling text, refer to the Scrolling Message Text section later in this manual). Select the desired setting in the list box using the up or down button. The range is 0-5 rows. The default setting is 0, which disables the message text feature.

¥Rows of SeparationÑSpecifies the number of blank rows to be set between the title/time/date text and the message text displays. Select the desired setting in the list box using the up or down button. The range is 0-28 rows. The default setting is 0.

¥Display TimeÑSpecifies the number of seconds that message text is to be displayed. Enter a value ranging from 0-9999 seconds. The default setting is 0, which allows the message text to be displayed for an indefinite period of time or until the message text is overwritten.

8.Send the formatting changes set in step 7 above to the selected unit and channel(s) by clicking the Send Current Formatting button, which is located below the Sample Display screen.

The Sample Display screen then displays the current formatting determined by the Format, Rows to Display, and Rows of Separation settings selected in step 7. In addition, the default message text for each row to be displayed appears. The default message text for rows 1-5 is as follows: Row 1 Message, Row 2 Message, Row 3 Message, Row 4 Message, and Row 5 Message.

Figure 33 provides an example of a Sample Display screen and the associated formatting settings (titles on top, three rows to display, and two rows of separation).

Note that the Sample Display does not show the actual position of the title/time/date and message text on the monitor on which the text is to be displayed but rather shows the position of the title/time/date text in relation to the message text. The actual positioning of the text is shown in the Position Text dialog box:

¥If message text is set and Titles on Top is set as the format, the Position Text dialog box shows the positioning of the title/time/date text.

¥If message text is set and Messages on Top is set as the format, the Position Text dialog box shows the positioning of the message text.

(For additional information about the Position Text dialog box, refer to the Set Display section of this manual.)

36

 

Pelco Manual C573M-D (11/03)

 

 

 

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Important Notice System Contents List of Tables List of IllustrationsMaster MDA Time and Date Generator for 63 MDA Slave Units CM9760-CC1 Connection to over 16 MDA UnitsDescription Important Safeguards and WarningsOverview System Configuration Rear Panel View Mounting Hardware SetupModels CommunicationSwitch Settings Port Setup Selected Communication Ports SetupSwitch Settings Camera Range Selected Address Setup for Daisy ChainingCameras Resetting to Factory Defaults Setting UP a Unit AS the Master ClockVideo Connections Clearing TITLE/TIME/DATE Text Display on ALL ChannelsCable Type Maximum Distance Data Connections Connecting the MDA to a System 9740/9760 ControllerPin Out RS-232 Function RS-422 Function RS-485 Function Connecting the MDA to AN External PCTransmit Transmit + No Connection Ground Receive Receive + Connecting the MDA to a KBD200A or KBD300A Keyboard Connecting the MDA to a CM9760-KBD KeyboardPower Connections Keyboard WiringProgramming Time and Date SetupProgramming Methods Programming with a KeyboardÒhost Direct CAM CTRL.Ó Entering the Programming Mode with the CM9760-KBDSET Camera Title Main MenuSET Camera Display SET Cable CompensationEnable Video Enable TimePosition DisplayDEC-31-02 SET Time and Date115952 PM Table E. CM9760-CC1/CM9760-MDA Format MatchupProtocol SET PortBaud Rate Data BitsSystem Requirements Reset MDAStop Bits ParityInstalling the CM9760-MDA Setup Program Login Dialog Box Starting the CM9760-MDA Setup ProgramSET Password CM9760-MDA Setup Dialog BOXSET System SET Unit IDEnter the Unit ID number 1-64, and then click OK System Communication Setup Dialog Box Set Time and Date Dialog Box CM9760-CC1 CM9760-MDA SET TitlesPelco Manual C573M-D 11/03 Set Cable Compensation Dialog Box SET Display Position Text Dialog Box Message Text Editing Dialog Box SET Message TextCommand Data Window Pelco Manual C573M-D 11/03 Sample Display Screen Example Sample Command Data Window Pelco Manual C573M-D 11/03 Video Alphanumeric Overlays Send DataSymptom Possible Problem Possible Solution TroubleshootingSpecifications Ratings GeneralAppendix a Applications Simple System Configuration Shielded Twisted Pair RS-422 RS-232 CM9760-MDACM9760-CDU-T PV130CM9760-CC1 Connection to up to 16 Daisy-Chained MDA Units COM1 COM2 MDA Connected to Multiplexers = Data Non-Coaxitron System SetupCoaxitron with System 9760 Setup Coaxitron with System 6800 Setup CM9760-MDA Message Text Sent from Third-Party Equipment Asterisk Appendix B Supported Title and Message Text CharactersCommand Function Command Format Appendix C Message Text Insertion CommandsPelco Manual C573M-D 11/03 Radio and Television Interference Regulatory NoticesRevision History Warranty and Return Information
Top Page Image Contents