Pelco cs73m-d operation manual Regulatory Notices, Radio and Television Interference

Page 60

REGULATORY NOTICES

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

¥Reorient or relocate the receiving antenna.

¥Increase the separation between the equipment and the receiver.

¥Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

¥Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: ÒHow to Identify and Resolve Radio-TV Interference Problems.Ó This booklet is available from the U.S. Govern- ment Printing Office, Washington D.C. 20402.

Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communica- tions CommissionÕs rules.

Pelco Manual C573M-D (11/03)

59

Image 60

Contents Important Notice System Contents List of Illustrations List of TablesMaster MDA Time and Date Generator for 63 MDA Slave Units CM9760-CC1 Connection to over 16 MDA UnitsImportant Safeguards and Warnings DescriptionOverview System Configuration Rear Panel View Hardware Setup MountingModels CommunicationCommunication Ports Setup Switch Settings Port Setup SelectedAddress Setup for Daisy Chaining Switch Settings Camera Range SelectedCameras Setting UP a Unit AS the Master Clock Resetting to Factory DefaultsClearing TITLE/TIME/DATE Text Display on ALL Channels Video ConnectionsCable Type Maximum Distance Connecting the MDA to a System 9740/9760 Controller Data ConnectionsConnecting the MDA to AN External PC Pin Out RS-232 Function RS-422 Function RS-485 FunctionTransmit Transmit + No Connection Ground Receive Receive + Connecting the MDA to a CM9760-KBD Keyboard Connecting the MDA to a KBD200A or KBD300A KeyboardKeyboard Wiring Power ConnectionsTime and Date Setup ProgrammingProgramming Methods Programming with a KeyboardEntering the Programming Mode with the CM9760-KBD Òhost Direct CAM CTRL.ÓMain Menu SET Camera TitleSET Cable Compensation SET Camera DisplayEnable Time Enable VideoPosition DisplaySET Time and Date DEC-31-02115952 PM Table E. CM9760-CC1/CM9760-MDA Format MatchupSET Port ProtocolBaud Rate Data BitsReset MDA System RequirementsStop Bits ParityInstalling the CM9760-MDA Setup Program Starting the CM9760-MDA Setup Program Login Dialog BoxCM9760-MDA Setup Dialog BOX SET PasswordSET Unit ID SET SystemEnter the Unit ID number 1-64, and then click OK System Communication Setup Dialog Box Set Time and Date Dialog Box SET Titles CM9760-CC1 CM9760-MDAPelco Manual C573M-D 11/03 Set Cable Compensation Dialog Box SET Display Position Text Dialog Box SET Message Text Message Text Editing Dialog BoxCommand Data Window Pelco Manual C573M-D 11/03 Sample Display Screen Example Sample Command Data Window Pelco Manual C573M-D 11/03 Send Data Video Alphanumeric OverlaysTroubleshooting Symptom Possible Problem Possible SolutionSpecifications General RatingsAppendix a Applications Simple System Configuration Shielded Twisted Pair RS-232 CM9760-MDA RS-422PV130 CM9760-CDU-TCM9760-CC1 Connection to up to 16 Daisy-Chained MDA Units COM1 COM2 MDA Connected to Multiplexers Non-Coaxitron System Setup = DataCoaxitron with System 9760 Setup Coaxitron with System 6800 Setup CM9760-MDA Message Text Sent from Third-Party Equipment Appendix B Supported Title and Message Text Characters AsteriskAppendix C Message Text Insertion Commands Command Function Command FormatPelco Manual C573M-D 11/03 Regulatory Notices Radio and Television InterferenceWarranty and Return Information Revision History