Novatel OM-20000122 user manual FCC Notices, Industry Canada, CE Notice

Page 8

Notices

The following notices apply to the SPAN-CPT.

FCC Notices

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SPAN-CPT complies with the radiated and conducted emission limits for a Class B digital device. The Class B limits are designed to provide reasonable protection against harmful interference in a residential installation.

The equipment listed generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Re-orient or relocate the receiving antenna

•Increase the separation between the equipment and the receiver

•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected

•Consult the dealer or an experienced radio/TV technician for help

use properly shielded interface cables (such as Belden #9539 or equivalent) when using the serial data ports, and double-shielded cables (such as Belden #9945 or equivalent) when using the I/O strobe port.In order to maintain compliance with the limits of a Class B digital device, it is required to

 Changes or modifications to this equipment, not expressly approved by NovAtel Inc., could result in violation of FCC, Industry Canada and CE Marking rules and void the user’s authority to operate this equipment.

Industry Canada

SPAN-CPT Class B digital apparatuses comply with Canadian ICES-003.

SPAN-CPT appareils numérique de la classe B sont conforme à la norme NMB-003 du Canada.

CE Notice

The enclosures carry the CE mark.

"SPAN-CPT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC."

8	SPAN-CPT User Manual Rev 8

Image 8

Contents SPAN-CPT Warranty Return instructions Proprietary NoticeTable of Contents Technical Specifications Figures Tables NovAtel Knowledge Base Before Contacting Customer Support Contact InformationCE Notice FCC NoticesIndustry Canada Lightning Protection Installation and Grounding Procedure What is the hazard?Weee Notice Hazard ImpactPrimary and Secondary Lightning Protection Ref # Description Introduction Fundamentals of GNSS+INSConventions System ComponentsRelated Documents and Information SPAN-CPT Installation Required EquipmentManuals SPAN-CPT HardwareHardware Set Up Typical SPAN-CPT Set Up Radio COM2Mount the Antenna Mount the SPAN-CPTConnect Power Connect the Gnss AntennaConnect a Computer to the SPAN-CPT Connect the I/O Strobe SignalsBattery Isolator Auxiliary Vehicle MainBattery Odometer Requirements Can BusOdometer Connection Cable Modification for Kistler WPT Cable Cable Modification for SPAN-CPT CableLocal Level Frame SPAN-CPT OperationDefinition of Reference Frames Within Span Span Body Frame Full Mapping DefinitionsEnclosure Frame Vehicle FrameCommunicating with the SPAN-CPT System Use NovAtel Connect to CommunicateChapter SPAN-CPT Operation Software Configuration Gnss ConfigurationSpan IMU Configuration SPAN-CPT Configuration with NovAtel ConnectReal Time Operation System Start-Up and Alignment Techniques AsciiDefault Kinematic Alignment SetimuorientationDual Antenna Alignment Navigation ModeManual Alignment Course Over Ground Wheel Sensor Update LogicAzimuth Sources on a Span System Logs with Azimuth data Inertial AzimuthAlign Azimuth Solution Parameters Data Collection Logging Restriction Data Collection for Post-ProcessingNovAtel Correct with TerraStar Variable Lever ArmEnabling L-Band Veripos Marine Subscriptions OmniSTARChapter SPAN-CPT Operation Installation SPAN-CPT Dual-AntennaConfiguring Span with Align on SPAN-CPT Power SupplyChapter SPAN-CPT Dual-Antenna SecondaryUnaided Alignment Alignment on a Moving Vessel Aided Transfer AlignmentAlignment on a Stationary Vehicle Aided Static Alignment Span Align Attitude Updates Automatic Alignment Mode Automatic Alignment defaultNovAtel Firmware and Software Firmware Updates and Model UpgradesFirmware Updates Authorization Code Model UpgradesTypes of Firmware Files Updating or Upgrading Using the WinLoad UtilityTransferring Firmware Files Using the WinLoad Utility Open a File to DownloadUpdating using SoftLoad Commands Searching for CardWorking with S-Records Softloadsrec S-RECORDUpgrade Procedure Upgrading Using the Auth CommandKey Firmware Commands Technical Specifications SPAN-CPT Technical SpecificationsHardware Specification for SPAN-CPT KVH IMU Sensor SpecificationsElectrical and Environmental Specifications Power SpecificationsSPAN-CPT Mechanical Drawings SPAN-CPT Side and Perspective ViewSPAN-CPT Top, Front and Bottom View SPAN-CPT Cable SPAN-CPT 60723108 KVH Development Terminated Cable Pin-OutFemale Male Pin Function Wire Pair Wire Color SPAN-CPT 60723107 KVH Standard Un-terminated Cable Pin-OutSPAN-CPT System Replacement PartsAccessories and Options Frequently Asked Questions Appendix COM-20000122 Rev March