Novatel OM-20000122 user manual Veripos Marine Subscriptions, OmniSTAR

Page 35

SPAN-CPT Operation

Chapter 3

 

 

3.9.2Veripos Marine Subscriptions

Veripos. A unit with a marine subscription can not be switched to a land subscription and vice versa.Subscriptions to the Veripos Apex and Ultra marine services must be obtained directly from

A subscription is required to use the Veripos services. Contact Veripos sales at www.veripos.com/ support.html to obtain a Service Access License (SAL) number. To activate the service, contact the Veripos Help Desk at +44 (0) 1224 527 104 or visit www.veripos.com/support.html. Provide the SAL number and the receiver's Veripos Serial Number (VSN). To obtain the receiver-specific VSN, enter the following command:

log veriposinfo

The log displays the VSN in the first field following the log header and also displays the status of your subscription.

To activate a subscription, the receiver must be powered and tracking an L-Band Veripos satellite prior to the planned activation time. Use the ASSIGNLBANDBEAM command to configure the receiver to track the Veripos satellite.

The latest services and coverage can be obtained from www.veripos.com. For additional information on Veripos activation, contact NovAtel Customer Service at www.novatel.com/ support or download the APN-062 NovAtel CORRECT with Veripos from: www.novatel.com/support/search/items/Application%20Note.

3.9.3OmniSTAR

®

OmniSTAR service is not supported for OEM6 products sold after October 24, 2013. If unsure whether the receiver is OmniSTAR capable, contact NovAtel Sales at www.novatel.com/where-to-buy/sales-offices, NovAtel Customer Support at www.novatel.com/support or visit www.novatel.com/products/novatel-correct.

A subscription is required to use the OmniSTAR service. To obtain a subscription, contact OmniSTAR at 1-888-883-8476 or 713-785-5850. Provide the receiver’s OmniSTAR serial number (which is different from the NovAtel serial number). To obtain the OmniSTAR serial number, enter the following command:

log lbandinfo

The log displays the L-Band serial number in the fifth field following the log header. The log also provides the status of your subscription. Refer to the LBANDINFO log in the OEM6 Family Firmware Reference Manual (OM-20000129) for more information.

To activate the subscription, the receiver must be powered and tracking an L-Band satellite. When advised by OmniSTAR of the appropriate satellite frequency and data link rate for your location, use the ASSIGNLBAND command to configure your receiver.

The latest frequencies can be obtained from: www.omnistar.com.

Example:

assignlband omnistar 1557855 1200

To confirm tracking of an L-Band signal, log the L-Band status information by entering the following command:

log lbandstat

SPAN-CPT User Manual Rev 8

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents SPAN-CPT Return instructions Proprietary Notice WarrantyTable of Contents Technical Specifications Figures Tables Contact Information NovAtel Knowledge Base Before Contacting Customer SupportCE Notice FCC NoticesIndustry Canada Hazard Impact Lightning Protection Installation and Grounding ProcedureWhat is the hazard? Weee NoticePrimary and Secondary Lightning Protection Ref # Description Fundamentals of GNSS+INS IntroductionConventions System ComponentsRelated Documents and Information SPAN-CPT Hardware SPAN-CPT InstallationRequired Equipment ManualsTypical SPAN-CPT Set Up Radio COM2 Hardware Set UpMount the SPAN-CPT Mount the AntennaConnect the Gnss Antenna Connect PowerConnect a Computer to the SPAN-CPT Connect the I/O Strobe SignalsBattery Isolator Auxiliary Vehicle MainBattery Odometer Requirements Can BusOdometer Connection Cable Modification for SPAN-CPT Cable Cable Modification for Kistler WPT CableLocal Level Frame SPAN-CPT OperationDefinition of Reference Frames Within Span Full Mapping Definitions Span Body FrameVehicle Frame Enclosure FrameUse NovAtel Connect to Communicate Communicating with the SPAN-CPT SystemChapter SPAN-CPT Operation SPAN-CPT Configuration with NovAtel Connect Software ConfigurationGnss Configuration Span IMU ConfigurationReal Time Operation Ascii System Start-Up and Alignment TechniquesSetimuorientation Default Kinematic AlignmentDual Antenna Alignment Navigation ModeManual Alignment Course Over Ground Wheel Sensor Update LogicAzimuth Sources on a Span System Logs with Azimuth data Inertial AzimuthAlign Azimuth Data Collection Solution ParametersData Collection for Post-Processing  Logging RestrictionNovAtel Correct with TerraStar Variable Lever ArmEnabling L-Band OmniSTAR Veripos Marine SubscriptionsChapter SPAN-CPT Operation SPAN-CPT Dual-Antenna InstallationSecondary Configuring Span with Align on SPAN-CPTPower Supply Chapter SPAN-CPT Dual-AntennaUnaided Alignment Alignment on a Moving Vessel Aided Transfer AlignmentAlignment on a Stationary Vehicle Aided Static Alignment Automatic Alignment Mode Automatic Alignment default Span Align Attitude UpdatesNovAtel Firmware and Software Firmware Updates and Model UpgradesFirmware Updates Model Upgrades Authorization CodeTypes of Firmware Files Updating or Upgrading Using the WinLoad UtilityTransferring Firmware Files Open a File to Download Using the WinLoad UtilitySearching for Card Updating using SoftLoad CommandsSoftloadsrec S-RECORD Working with S-RecordsUpgrade Procedure Upgrading Using the Auth CommandKey Firmware Commands KVH IMU Sensor Specifications Technical SpecificationsSPAN-CPT Technical Specifications Hardware Specification for SPAN-CPTPower Specifications Electrical and Environmental SpecificationsSPAN-CPT Side and Perspective View SPAN-CPT Mechanical DrawingsSPAN-CPT Top, Front and Bottom View SPAN-CPT 60723108 KVH Development Terminated Cable Pin-Out SPAN-CPT CableFemale Male SPAN-CPT 60723107 KVH Standard Un-terminated Cable Pin-Out Pin Function Wire Pair Wire ColorSPAN-CPT System Replacement PartsAccessories and Options Appendix C Frequently Asked QuestionsOM-20000122 Rev March
Top Page Image Contents