JVC RX-554RBK manual Basic Operations, On the front panel, From the remote control

Page 14

English

Basic Operations

The following operations are commonly used when you play any sound source.

Turning the Power On and Off (Standby)

On the front panel:

To turn on the power, press STANDBY/ON .

The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.

STANDBY

STANDBY/ON

MUTE TUNED	SLEEP SEA	3D-PHONIC L		R
AUTO STEREO PRO LOGIC 3CH LOGIC HALL		LOUDNESS	VOLUME
DAP				TA
				TA
CH-			MHz	NEWS
			MHz	INFO
			kHz	INFO

Current source name appears	Current volume
	level is shown here

To turn off the power (into standby mode), press STANDBY/ON

again.

The STANDBY lamp lights up.

From the remote control:

To turn on the power, press AUDIO.

The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.

To turn off the power (into standby mode), press AUDIO again.

The STANDBY lamp lights up.

Selecting the Source to Play

AUDIO

Note:

A small amount of power is consumed in standby mode. To turn the power off completely, press POWER to set it in the ÑOFF position on the front panel.

On the front panel:

1. Press SOURCE so that the Control %/ Þbuttons	SOURCE

work for selecting the source.

The lamp above the button lights up.

2.Press Control % / Þuntil the source name you want appears on the display.

VOLUME

From the remote control:

Press one of the source buttons directly.

CD*	Listen to the CD player.
TAPE*	Listen to the cassette deck.
TUNER/BAND*	Listen to the radio. Each time you press the
	button, the band alternates between FM and
	AM (MW/LW).
VCR	View the playback picture from the VCR.
VIDEO	View the video component connected to the
	VIDEO jacks.
PHONO*	Listen to a record.

CD

TAPE

TUNER/

BAND

VCR

VIDEO

PHONO

Note:

When you press one of the source buttons on the remote control marked with an asterisk (*), the receiver automatically turns on.

9

Image 14

Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Front Panel Remote ControlParts Identification Locations Getting StartedGeneral Handling the receiverUsing the Standard Type Connector Not supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Getting StartedAbout the speaker impedance 16 ohmVideo component connections Connecting Other ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely Basic Operations From the remote controlTurning the Power On and Off Standby On the front panelOn the front panel only From the remote control onlyAdjusting the Volume Selecting the Front SpeakersBasic Operations Listening with HeadphonesTo listen with only headphones Recording a SourceListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep TimerTo cancel the Sleep Timer Basic SettingsWhen the shut-off time comes Selecting the Center Speaker SizeTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Receiving Radio Broadcasts Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? Press PTY Search again To search for a program using the PTY codesSearching for a Program by PTY Codes To continue searching after the first stopPress PTY Search while listening to an FM station Display gives you the PTY codes described onDescriptions of the PTY codes Traffic Announcement in your area Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goesTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Using the Preset SEA Modes Press SEA Preset to select the effect levelActivating the Surround Sounds On JVC 3D Phonic modeOn the DAP mode On surround modes3DACTION Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DTHEATRMark Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Press Effect to select the effect levelHall Using the DAP ModesPavilion Gives clear vocal and the feeling of a concert hallSelect OFF in step DAP indicator goes off from the display Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Press Rear +/- to adjust the rear speaker output levelSpeaker Arrangements for Surround Modes Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode This casePrologic Preparing for Surround ModesTheater 3CHLOGICWide Press Control @/ # to select the center modeDelay NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayBalance Press Effect to adjust the effect levelPress Test to start checking the speaker output Press Test again to stop the test toneFrom the front panel Using Surround ModesTo cancel surround mode Work for selecting the surround/DAP/3D-PHONIC ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTo operate JVC audio components using this remote control Operating Other ComponentsOperating Other Components Standby/On sectionTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierGeneral FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT