JVC RX-554RBK One Touch Operation, To store the sound settings, To recall the sound settings

Page 19

One Touch Operation

This receiver can memorize the optimum sound settings for each playing source.

English

About the One Touch Operation

JVC’s One Touch Operation function is used to assign and store different sound settings for each different playing source. By using this function, you do not have to change the settings every time you change the source. The stored settings for the newly selected source are automatically recalled.

The following can be stored for each source:

Volume level (see page 10)

Balance (see page 12)

Loudness (see page 12)

Preset SEA modes (see page 24)

3D-PHONIC mode settings (see page 27)

DAP mode settings (see page 29)

Surround mode settings (see page 36)

Using the One Touch Operation

To store the sound settings

1. Press ONE TOUCH OPERATION.

The ONE TOUCH OPERATION lamp lights up, then

ONE TOUCH OPERATION

the previously memorized settings are recalled and appear on the display in turn.

2.Adjust the sound using the functions listed above. The newly adjusted settings are memorized.

To recall the sound settings

 

With the ONE TOUCH OPERATION lamp lit, the settings

ONE TOUCH

for the currently selected source is recalled, and appears on

OPERATION

 

the display when the source is selected.

 

To cancel the One Touch Operation function

Press ONE TOUCH OPERATION so that the lamp goes off.

(Even though the One Touch Operation function is canceled, the recalled sound effects remain active.)

Note:

If the source is TUNER/BAND, the One Touch Operation function memorizes the settings each for the FM and AM band.

The DAP mode, surround mode and 3D-PHONIC mode cannot be used at the same time.

14

Image 19
Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Parts Identification Remote ControlFront Panel Handling the receiver Getting StartedGeneral LocationsFM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna Using the Standard Type Connector Not suppliedGetting Started Connecting the front speakersConnecting the rear and center speakers Connecting the Speakers16 ohm About the speaker impedanceIf your audio components have a Compu LINK-3 terminals Connecting Other ComponentsAudio component connections Video component connectionsTo shut off the power completely Connecting the Power CordPutting Batteries in the Remote Control On the front panel From the remote controlTurning the Power On and Off Standby Basic OperationsSelecting the Front Speakers From the remote control onlyAdjusting the Volume On the front panel onlyRecording a Source Listening with HeadphonesTo listen with only headphones Basic OperationsUsing the Sleep Timer Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessSelecting the Center Speaker Size Basic SettingsWhen the shut-off time comes To cancel the Sleep TimerOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Press TUNER/BAND so that the Control %/ Þ/ @ Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Receiving Radio BroadcastsWhat Information Can RDS Signals Provide? To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes Press PTY Search againDisplay gives you the PTY codes described on Press PTY Search while listening to an FM stationDescriptions of the PTY codes News Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode Traffic Announcement in your areaPress EON so that the program type TA/NEWS/INFO goes To stop listening to the program selected by EONSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn surround modes On JVC 3D Phonic modeOn the DAP mode Activating the Surround Sounds3DTHEATR Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DACTIONPress Effect to select the effect level Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode MarkGives clear vocal and the feeling of a concert hall Using the DAP ModesPavilion HallPress Rear +/- to adjust the rear speaker output level Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Select OFF in step DAP indicator goes off from the displayThis case Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode Speaker Arrangements for Surround Modes3CHLOGIC Preparing for Surround ModesTheater PrologicNormal Press Control @/ # to select the center modeDelay WideDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test again to stop the test tone Press Effect to adjust the effect levelPress Test to start checking the speaker output BalanceWork for selecting the surround/DAP/3D-PHONIC Modes Using Surround ModesTo cancel surround mode From the front panelSynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionOperating Other Components To operate JVC audio components using this remote controlStandby/On section Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsAM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT