JVC RX-554RBK manual Operating Other Components, Standby/On section

Page 44

Operating Other Components

English

IMPORTANT:

To operate JVC video components using this remote control:

•Aim the remote control directly at the remote sensor on the VCR or TV, not on the receiver.

Note:

If you choose a source on the front panel, the remote control will not operate that source.

7After pressing VCR, you can perform the following operations on the VCR:

3Starts playback.

4 Rewinds a video tape. ¢ Fast winds a video tape.

7Stops operation.

8Pauses. To resume playing, press 3.

You can always do the following on the VCR:

•Change the channels on the VCR using the VCR CH +/–button.

•Turn on and off the VCR by pressing VCR in

the (Standby/On) section.

7You can always perform the following operations on the TV:

•Change the TV’s input mode to either “TV” or “VIDEO” using the TV/VIDEO button.

•Change the TV volume using the TV VOL. +/– button.

•Change the channels on the TV using the TV CH +/–button.

•Turn on and off the TV by pressing TV in the

(Standby/On) section.

CD TV VCR AUDIO

	TAPE	DAP MODE	3D-PHONIC	SURROUND
	TAPE	1	2	3
	TUNER/	EFFECT	DELAY	TEST
	BAND	4	5	6
	VCR	SEA MODE	– REAR +
	VCR	7/P	8	9
		7/P	8	9
	VIDEO	SEA	– CENTER +
	VIDEO	PRESET	10	+10
		PRESET	10	+10
	PHONO	SOUND		ONE TOUCH
		CONTROL CD-DISC OPERATION
	– TV CH +		– VCR CH +
	– TV VOL. +		PTY SEARCH	DISPLAY
	– TV VOL. +

TV/

VIDEO

–PTY SELECT +

– VOLUME + MUTING

RM-SR554RU REMOTE CONTROL

Notes:

• If you press SOUND CONTROL, you cannot operate the VCR with this remote control. If this happens, press VCR again, so operating buttons for video components will work for the VCR.

•If you press the VCR (the one for the source selection) on the remote control aiming at a JVC TV, the TV’s input mode will change to the video input.

39

Image 44

Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Front Panel Remote ControlParts Identification Getting Started GeneralLocations Handling the receiverConnecting the FM and AM MW/LW Antennas Using the Supplied FM AntennaUsing the Standard Type Connector Not supplied FM Antenna ConnectionsConnecting the front speakers Connecting the rear and center speakersConnecting the Speakers Getting StartedAbout the speaker impedance 16 ohmConnecting Other Components Audio component connectionsVideo component connections If your audio components have a Compu LINK-3 terminalsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely From the remote control Turning the Power On and Off StandbyBasic Operations On the front panelFrom the remote control only Adjusting the VolumeOn the front panel only Selecting the Front SpeakersListening with Headphones To listen with only headphonesBasic Operations Recording a SourceBasic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep TimerBasic Settings When the shut-off time comesTo cancel the Sleep Timer Selecting the Center Speaker SizeTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Selecting the FM Reception Mode Using the RDS Radio Data System to Receive FM StationsReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? To search for a program using the PTY codes Searching for a Program by PTY CodesPress PTY Search again To continue searching after the first stopPress PTY Search while listening to an FM station Display gives you the PTY codes described onDescriptions of the PTY codes Switching to a Broadcast Program of Your Choice Temporarily Receiver enters EON standby modeTraffic Announcement in your area NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goesTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Using the Preset SEA Modes Press SEA Preset to select the effect levelOn JVC 3D Phonic mode On the DAP modeActivating the Surround Sounds On surround modesUsing JVC 3D-PHONIC Modes Activating the Surround Sounds3DACTION 3DTHEATRPress Control @ / #to adjust the effect level To cancel the 3D-PHONIC modeMark Press Effect to select the effect levelUsing the DAP Modes PavilionHall Gives clear vocal and the feeling of a concert hallPress Control @/ #to adjust the rear speaker output level To cancel the DAP modeSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This casePreparing for Surround Modes TheaterPrologic 3CHLOGICPress Control @/ # to select the center mode DelayWide NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayPress Effect to adjust the effect level Press Test to start checking the speaker outputBalance Press Test again to stop the test toneUsing Surround Modes To cancel surround modeFrom the front panel Work for selecting the surround/DAP/3D-PHONIC ModesCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingTo operate JVC audio components using this remote control Operating Other ComponentsOperating Other Components Standby/On sectionTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierGeneral FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT