JVC RX-554RBK manual Basic Operations, Recording a Source, Listening with Headphones

Page 16

Basic Operations

English

Recording a Source

You can record any source playing through the receiver to a cassette deck connected to the TAPE jacks and the VCR connected to the VCR jacks at the same time.

While recording, you can listen to the selected sound source at whatever sound level you like, without affecting the sound levels of the recording.

Listening with Headphones

A standard pair of headphones can be connected to the PHONES jack on the front panel. Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

To listen with only headphones

 

 

Press both SPEAKERS 1 and 2 to set them in the ÑOFF position.

1

2

 

 

SPEAKERS

_ON ÑOFF

Note:

The output volume level, preset SEA, DAP, 3D-PHONIC and surround modes cannot affect the recording.

Note:

The SPEAKERS 1 and 2 do not affect the sound output of the center and rear speakers.

11

Image 16
Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Parts Identification Remote ControlFront Panel Getting Started GeneralLocations Handling the receiverConnecting the FM and AM MW/LW Antennas Using the Supplied FM AntennaUsing the Standard Type Connector Not supplied FM Antenna ConnectionsConnecting the front speakers Connecting the rear and center speakersConnecting the Speakers Getting StartedAbout the speaker impedance 16 ohmConnecting Other Components Audio component connectionsVideo component connections If your audio components have a Compu LINK-3 terminalsTo shut off the power completely Connecting the Power CordPutting Batteries in the Remote Control From the remote control Turning the Power On and Off StandbyBasic Operations On the front panelFrom the remote control only Adjusting the VolumeOn the front panel only Selecting the Front SpeakersListening with Headphones To listen with only headphonesBasic Operations Recording a SourceBasic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep TimerBasic Settings When the shut-off time comesTo cancel the Sleep Timer Selecting the Center Speaker SizeTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Selecting the FM Reception Mode Using the RDS Radio Data System to Receive FM StationsReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? To search for a program using the PTY codes Searching for a Program by PTY CodesPress PTY Search again To continue searching after the first stopPress PTY Search while listening to an FM station Display gives you the PTY codes described onDescriptions of the PTY codes Switching to a Broadcast Program of Your Choice Temporarily Receiver enters EON standby modeTraffic Announcement in your area NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goesSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelOn JVC 3D Phonic mode On the DAP modeActivating the Surround Sounds On surround modesUsing JVC 3D-PHONIC Modes Activating the Surround Sounds3DACTION 3DTHEATRPress Control @ / #to adjust the effect level To cancel the 3D-PHONIC modeMark Press Effect to select the effect levelUsing the DAP Modes PavilionHall Gives clear vocal and the feeling of a concert hallPress Control @/ #to adjust the rear speaker output level To cancel the DAP modeSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This casePreparing for Surround Modes TheaterPrologic 3CHLOGICPress Control @/ # to select the center mode DelayWide NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayPress Effect to adjust the effect level Press Test to start checking the speaker outputBalance Press Test again to stop the test toneUsing Surround Modes To cancel surround modeFrom the front panel Work for selecting the surround/DAP/3D-PHONIC ModesCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingTo operate JVC audio components using this remote control Operating Other ComponentsOperating Other Components Standby/On sectionTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT