JVC RX-554RBK manual Preparing for Surround Modes, Theater, Prologic, 3CHLOGIC

Page 37

Preparing for Surround Modes

Once you have set the surround modes, you can use the same adjustment every time you want to activate the surrround mode you want. The receiver memorizes surround adjustments for each mode.

On the front panel:
1. Press SURROUND so that the Control %/ Þbuttons	SURROUND
work for selecting the surround modes.

The lamp above the button lights up.

2.Press Control % / Þ to select one of the surround mode (“PROLOGIC”, “3CHLOGIC” or

“THEATER”).

Each time you press the button, the surround modes change as follows:

Ex.

PROLOGIC

THEATER

3CHLOGIC

OFF

3DACTION*

PAVILION*

PROLOGIC

Select this mode when you use a center speaker and rear

speakers.

THEATER

Select this mode to watch a video source with Dolby Surround

when you have connected the rear speakers (and a center

speaker). This mode gives you the feeling of a movie theater.

3CHLOGIC

Select this mode when you use a center speaker without rear

speakers.

OFF

Select this to turn off the surround/DAP/3D-PHONIC modes.

*You cannot select the 3D-PHONIC modes or the DAP modes in this step. For the 3D-PHONIC modes: see pages 27 and 28.

For the DAP modes: see pages 29 and 30.

3. Press ADJUST so that the Control %/ Þ / @ / #	ADJUST
buttons work for adjusting the selected surround
mode.

The lamp above the button lights up.

4. Press Control % / Þ until “CNT MODE” (Center Mode) appears on the display.

Continued to the next page.

English

Note:

When one of the surround modes is selected, the corresponding indicator lights up on the display.

Note:

If you have already set the center speaker size following the procedure described on page 13, you do not have to select the center mode in this procedure.

32

Image 37

Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Parts Identification Remote ControlFront Panel General Getting StartedLocations Handling the receiverUsing the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasUsing the Standard Type Connector Not supplied FM Antenna ConnectionsConnecting the rear and center speakers Connecting the front speakersConnecting the Speakers Getting Started16 ohm About the speaker impedanceAudio component connections Connecting Other ComponentsVideo component connections If your audio components have a Compu LINK-3 terminalsTo shut off the power completely Connecting the Power CordPutting Batteries in the Remote Control Turning the Power On and Off Standby From the remote controlBasic Operations On the front panelAdjusting the Volume From the remote control onlyOn the front panel only Selecting the Front SpeakersTo listen with only headphones Listening with HeadphonesBasic Operations Recording a SourceAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes Basic SettingsTo cancel the Sleep Timer Selecting the Center Speaker SizeTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Using the RDS Radio Data System to Receive FM Stations Selecting the FM Reception ModeReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? Searching for a Program by PTY Codes To search for a program using the PTY codesPress PTY Search again To continue searching after the first stopDisplay gives you the PTY codes described on Press PTY Search while listening to an FM stationDescriptions of the PTY codes Receiver enters EON standby mode Switching to a Broadcast Program of Your Choice TemporarilyTraffic Announcement in your area NewsPress EON so that the program type TA/NEWS/INFO goes To stop listening to the program selected by EONSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn the DAP mode On JVC 3D Phonic modeActivating the Surround Sounds On surround modesActivating the Surround Sounds Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRTo cancel the 3D-PHONIC mode Press Control @ / #to adjust the effect levelMark Press Effect to select the effect levelPavilion Using the DAP ModesHall Gives clear vocal and the feeling of a concert hallTo cancel the DAP mode Press Control @/ #to adjust the rear speaker output levelSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect 3CHLOGIC Select Normal or Wide for center mode Select Prologic or Theater Select Phantom for center modeSpeaker Arrangements for Surround Modes This caseTheater Preparing for Surround ModesPrologic 3CHLOGICDelay Press Control @/ # to select the center modeWide NormalDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output Press Effect to adjust the effect levelBalance Press Test again to stop the test toneTo cancel surround mode Using Surround ModesFrom the front panel Work for selecting the surround/DAP/3D-PHONIC ModesRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingOperating Other Components To operate JVC audio components using this remote controlStandby/On section Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsAM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT