JVC RX-554RBK manual Using the Preset SEA Modes, Selecting Your Favorite SEA Mode

Page 29

Using the Preset SEA Modes

The preset SEA (Sound Effect Amplifier) modes give you control of the way your music sounds.

English

Selecting Your Favorite SEA Mode

On the front panel:

1. Press PRESET SEA so that the Control %/ Þ / @ /

PRESET SEA

# buttons work for preset SEA setting.

The lamp above the button lights up.

2.Press Control % / Þuntil the preset SEA mode you want appears on the display.

The SEA indicator also lights up on the display.

Each time you press the button, the preset SEA modes change as follows:

Movie Sports Music

OFF

3.Press Control @ / # to select the effect level.

Each time you press the button, the effect level changes as follows:

When “Movie” is selected:

MOVIE 1MOVIE 2MOVIE 3

When “Sports” is selected:

SPORTS1SPORTS2SPORTS3

When “Music” is selected:

JAZZ 1JAZZ 2ROCK 1ROCK 2

COUNTRY2COUNTRY1MUSICAL2 MUSICAL1

Movie:	Adds breadth to sounds so you feel like you are in a movie theater.

Sports:	Makes sounds exciting.

Music:	Select one of the modes below.
	JAZZ:	Gives a feeling of a live atmosphere. Good for
		acoustic music.
	ROCK:	Gives a heavy sound. Both high and low frequencies
		are boosted.
	MUSICAL:	Enhances the mid-frequency range, which the human
		voice is mostly made up of.
	COUNTRY: Enhances the high-frequency range so that
		instruments such the violin and banjo are emphasized.

OFF:	No preset SEA mode is applied (See below).

To cancel the preset SEA mode

Select “OFF” in step 2 above.

The SEA indicator goes off from the display.

Notes:

•The preset SEA modes cannot be used for recording.

•When you turn on the preset SEA mode, the mode with its effect level previously selected is recalled at first.

24

Image 29

Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Front Panel Remote ControlParts Identification General Getting StartedLocations Handling the receiverUsing the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasUsing the Standard Type Connector Not supplied FM Antenna ConnectionsConnecting the rear and center speakers Connecting the front speakersConnecting the Speakers Getting Started16 ohm About the speaker impedanceAudio component connections Connecting Other ComponentsVideo component connections If your audio components have a Compu LINK-3 terminalsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely Turning the Power On and Off Standby From the remote controlBasic Operations On the front panelAdjusting the Volume From the remote control onlyOn the front panel only Selecting the Front SpeakersTo listen with only headphones Listening with HeadphonesBasic Operations Recording a SourceAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes Basic SettingsTo cancel the Sleep Timer Selecting the Center Speaker SizeTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Using the RDS Radio Data System to Receive FM Stations Selecting the FM Reception ModeReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? Searching for a Program by PTY Codes To search for a program using the PTY codesPress PTY Search again To continue searching after the first stopDisplay gives you the PTY codes described on Press PTY Search while listening to an FM stationDescriptions of the PTY codes Receiver enters EON standby mode Switching to a Broadcast Program of Your Choice TemporarilyTraffic Announcement in your area NewsPress EON so that the program type TA/NEWS/INFO goes To stop listening to the program selected by EONTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn the DAP mode On JVC 3D Phonic modeActivating the Surround Sounds On surround modesActivating the Surround Sounds Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRTo cancel the 3D-PHONIC mode Press Control @ / #to adjust the effect levelMark Press Effect to select the effect levelPavilion Using the DAP ModesHall Gives clear vocal and the feeling of a concert hallTo cancel the DAP mode Press Control @/ #to adjust the rear speaker output levelSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect 3CHLOGIC Select Normal or Wide for center mode Select Prologic or Theater Select Phantom for center modeSpeaker Arrangements for Surround Modes This caseTheater Preparing for Surround ModesPrologic 3CHLOGICDelay Press Control @/ # to select the center modeWide NormalDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output Press Effect to adjust the effect levelBalance Press Test again to stop the test toneTo cancel surround mode Using Surround ModesFrom the front panel Work for selecting the surround/DAP/3D-PHONIC ModesRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingOperating Other Components To operate JVC audio components using this remote controlStandby/On section Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsGeneral FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT