JVC RX-554RBK manual Per I’ltalia

Page 2

Warnings, Cautions and Others/Warnung, Achtung und sonstige Hinweise/ Mises en garde, précautions et indications diverses/Waarschuwingen, voorzorgen en andere mededelingen/Avisos, precauciones y otras notas/ Avvertenze e precauzioni da osservare

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

IMPORTANT.

DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Per I’ltalia:

“Si dichiara che il questo prodotto di marca JVC è conforme alle prescrizioni del Decreto Ministeriale n.548 del 28/08/95 pubblicato sulla Gazzetta Ufficiale della Repubblica Italiana n.301 del 28/12/95.”

G-1

Image 2
Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Front Panel Remote ControlParts Identification Locations Getting StartedGeneral Handling the receiverUsing the Standard Type Connector Not supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Getting StartedAbout the speaker impedance 16 ohmVideo component connections Connecting Other ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely Basic Operations From the remote controlTurning the Power On and Off Standby On the front panelOn the front panel only From the remote control onlyAdjusting the Volume Selecting the Front SpeakersBasic Operations Listening with HeadphonesTo listen with only headphones Recording a SourceListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep TimerTo cancel the Sleep Timer Basic SettingsWhen the shut-off time comes Selecting the Center Speaker SizeTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Receiving Radio Broadcasts Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? Press PTY Search again To search for a program using the PTY codesSearching for a Program by PTY Codes To continue searching after the first stopPress PTY Search while listening to an FM station Display gives you the PTY codes described onDescriptions of the PTY codes Traffic Announcement in your area Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goesTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Using the Preset SEA Modes Press SEA Preset to select the effect levelActivating the Surround Sounds On JVC 3D Phonic modeOn the DAP mode On surround modes3DACTION Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DTHEATRMark Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Press Effect to select the effect levelHall Using the DAP ModesPavilion Gives clear vocal and the feeling of a concert hallSelect OFF in step DAP indicator goes off from the display Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Press Rear +/- to adjust the rear speaker output levelSpeaker Arrangements for Surround Modes Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode This casePrologic Preparing for Surround ModesTheater 3CHLOGICWide Press Control @/ # to select the center modeDelay NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayBalance Press Effect to adjust the effect levelPress Test to start checking the speaker output Press Test again to stop the test toneFrom the front panel Using Surround ModesTo cancel surround mode Work for selecting the surround/DAP/3D-PHONIC ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTo operate JVC audio components using this remote control Operating Other ComponentsOperating Other Components Standby/On sectionTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierGeneral FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT