JVC RX-554RBK FM Antenna Connections, AM MW/LW Antenna Connections, Using the Supplied FM Antenna

Page 9

Connecting the FM and AM (MW/LW) Antennas

FM Antenna Connections

A.	B.
ANTENNA	ANTENNA
75	75
FM	FM
COAXIAL	COAXIAL
GND	GND
AM	AM
LOOP	LOOP
	FM Antenna
ANTENNA	Extend the FM antenna horizontally.

FM 75

COAXIAL

Outside FM Antenna wire

GND

AM

LOOP

AM

EXT

A. Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75 Ω COAXIAL terminal as temporary measure.

B.Using the Standard Type Connector (Not supplied)

A standard type connector (IEC or DIN45325) should be connected to the FM 75 Ω

COAXIAL terminal.

English

Note:

If reception is poor, connect the outside antenna.

Before attaching a 75 Ω coaxial cable (the kind with a round wire going to an outside antenna), disconnect the supplied FM wire antenna.

AM (MW/LW) Antenna Connections

ANTENNA

FM 75

COAXIAL

AM (MW/LW) Loop Antenna

GND

AM

LOOP

AM

EXT

123

Turn the loop until you have the best reception.

Snap the tabs on the loop into the slots of the base to assemble the AM (MW/LW) loop.

Outdoor Single Vinyl- covered Wire

Notes :

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM (MW/LW) loop antenna connected.)

4

Image 9

Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Remote Control Parts IdentificationFront Panel General Getting StartedLocations Handling the receiverUsing the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasUsing the Standard Type Connector Not supplied FM Antenna ConnectionsConnecting the rear and center speakers Connecting the front speakersConnecting the Speakers Getting Started16 ohm About the speaker impedanceAudio component connections Connecting Other ComponentsVideo component connections If your audio components have a Compu LINK-3 terminalsConnecting the Power Cord To shut off the power completelyPutting Batteries in the Remote Control Turning the Power On and Off Standby From the remote controlBasic Operations On the front panelAdjusting the Volume From the remote control onlyOn the front panel only Selecting the Front SpeakersTo listen with only headphones Listening with HeadphonesBasic Operations Recording a SourceAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes Basic SettingsTo cancel the Sleep Timer Selecting the Center Speaker SizeTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsTo cancel a stored preset station To tune in a preset stationPress 10 keys to select a preset channel number Using the RDS Radio Data System to Receive FM Stations Selecting the FM Reception ModeReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? Searching for a Program by PTY Codes To search for a program using the PTY codesPress PTY Search again To continue searching after the first stopDisplay gives you the PTY codes described on Press PTY Search while listening to an FM stationDescriptions of the PTY codes Receiver enters EON standby mode Switching to a Broadcast Program of Your Choice TemporarilyTraffic Announcement in your area NewsPress EON so that the program type TA/NEWS/INFO goes To stop listening to the program selected by EONUsing the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn the DAP mode On JVC 3D Phonic modeActivating the Surround Sounds On surround modesActivating the Surround Sounds Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRTo cancel the 3D-PHONIC mode Press Control @ / #to adjust the effect levelMark Press Effect to select the effect levelPavilion Using the DAP ModesHall Gives clear vocal and the feeling of a concert hallTo cancel the DAP mode Press Control @/ #to adjust the rear speaker output levelSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output levelSelect 3CHLOGIC Select Normal or Wide for center mode Select Prologic or Theater Select Phantom for center modeSpeaker Arrangements for Surround Modes This caseTheater Preparing for Surround ModesPrologic 3CHLOGICDelay Press Control @/ # to select the center modeWide NormalDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output Press Effect to adjust the effect levelBalance Press Test again to stop the test toneTo cancel surround mode Using Surround ModesFrom the front panel Work for selecting the surround/DAP/3D-PHONIC ModesRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingOperating Other Components To operate JVC audio components using this remote controlStandby/On section Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT