JVC RX-554RBK manual Specifications, Amplifier

Page 46

English

Specifications

Amplifier

Output Power

At Stereo operation

 

 

Front channels

55 watts per channel, min. RMS,

 

 

driven into 4 ohms at 1 kHz, with no

 

 

more than 0.9 % total harmonic

 

 

distortion. (IEC268-3/DIN)

 

 

30 watts per channel, min. RMS,

 

 

driven into 8 ohms at 1 kHz, with no

 

 

more than 0.9 % total harmonic

 

 

distortion. (IEC268-3/DIN)

 

 

30 watts per channel, min. RMS,

 

 

driven into 8 ohms, 40 Hz to 20 kHz,

 

 

with no more than 0.8 % total

 

 

harmonic distortion.

 

At Surround operation

 

 

Front channels

50 watts per channel, min. RMS,

 

 

driven into 8 ohms at 1 kHz, with no

 

 

more than 0.8 % total harmonic

 

 

distortion.

 

Center channel

50 watts, min. RMS, driven into 8

 

 

ohms at 1 kHz, with no more than 0.8

 

 

% total harmonic distortion.

 

Rear channel

50 watts, min. RMS, driven into 8

 

 

ohms at 1kHz, with no more than 0.8

 

 

% total harmonic distortion.

Total Harmonic Distortion (8 ohms, 1 kHz)

0.8 %* at 30 watts output

 

 

(* Measured by JVC Audio Analysis

 

 

System)

Frequency Response (8 ohms)

PHONO (MM)

20 Hz to 20 kHz (±1 dB)

 

CD, TAPE, VIDEO, VCR

20 Hz to 20 kHz (±1 dB)

Audio Input Sensitivity/Impedance (1 kHz)

PHONO

1.8 mV/47 k ohms

 

CD, TAPE, VIDEO, VCR

160 mV/47 k ohms

Audio Output Level

TAPE, VCR

160 mV

Signal-to-Noise Ratio (’66 IHF/DIN)

PHONO

70 dB/66 dB

 

CD, TAPE, VIDEO, VCR

87 dB/67 dB

RIAA Phono Equalization

±0.5 dB (20 Hz to 20 kHz)

Loudness control (Volume Control at –40 dB)

+5 ±2 dB at 100 Hz

41

Image 46
Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Parts Identification Remote ControlFront Panel Locations Getting StartedGeneral Handling the receiverUsing the Standard Type Connector Not supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Getting StartedAbout the speaker impedance 16 ohmVideo component connections Connecting Other ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalsTo shut off the power completely Connecting the Power CordPutting Batteries in the Remote Control Basic Operations From the remote controlTurning the Power On and Off Standby On the front panelOn the front panel only From the remote control onlyAdjusting the Volume Selecting the Front SpeakersBasic Operations Listening with HeadphonesTo listen with only headphones Recording a SourceListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep TimerTo cancel the Sleep Timer Basic SettingsWhen the shut-off time comes Selecting the Center Speaker SizeTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Receiving Radio Broadcasts Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? Press PTY Search again To search for a program using the PTY codesSearching for a Program by PTY Codes To continue searching after the first stopPress PTY Search while listening to an FM station Display gives you the PTY codes described onDescriptions of the PTY codes Traffic Announcement in your area Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goesSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelActivating the Surround Sounds On JVC 3D Phonic modeOn the DAP mode On surround modes3DACTION Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DTHEATRMark Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Press Effect to select the effect levelHall Using the DAP ModesPavilion Gives clear vocal and the feeling of a concert hallSelect OFF in step DAP indicator goes off from the display Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Press Rear +/- to adjust the rear speaker output levelSpeaker Arrangements for Surround Modes Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode This casePrologic Preparing for Surround ModesTheater 3CHLOGICWide Press Control @/ # to select the center modeDelay NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayBalance Press Effect to adjust the effect levelPress Test to start checking the speaker output Press Test again to stop the test toneFrom the front panel Using Surround ModesTo cancel surround mode Work for selecting the surround/DAP/3D-PHONIC ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTo operate JVC audio components using this remote control Operating Other ComponentsOperating Other Components Standby/On sectionTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT