JVC RX-554RBK manual FM tuner IHF, AM MW/LW tuner, General

Page 47

English

FM tuner (IHF)

Tuning Range		87.5 MHz to 108.0 MHz
Usable Sensitivity		12.7 dBf (1.2 µV/75 ohms)
50 dB Quieting Sensitivity	Monaural	16.3 dBf (1.8 µV/75 ohms)
	Stereo	38.3 dBf (22.5 µV/75 ohms)
Signal-to-Noise Ratio (IHF-A weighted)	Monaural	80 dB at 85 dBf
	Stereo	73 dB at 85 dBf
Total Harmonic Distortion	Monaural	0.15 % at 1 kHz
	Stereo	0.2 % at 1 kHz
Stereo Separation at REC OUT		40 dB at 1 kHz
Capture Ratio		1.5 dB (10 mV)
Alternate Channel Selectivity		60 dB: (±400 kHz)
Frequency Response		30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM (MW/LW) tuner
Tuning Range		522 kHz to 1,629 kHz (MW)
		144 kHz to 288 kHz (LW)
Usable Sensitivity	Loop antenna	300 µV/m (MW)
		600 µV/m (LW)
Signal-to-Noise Ratio		50 dB (100 mV/m)
General
Power Requirements		AC 230 V , 50 Hz
Power Consumption		240 watts
		5 watts (in standby mode)
Dimensions (W x H x D)		435 x 146 x 403 mm
		(17 3/16 x 5 3/4 x 15 7/8 inches)
Mass		8.5 kg (18.8 lbs )

Design & specifications are subject to change without notice.

Image 47

Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Front Panel Remote ControlParts Identification Handling the receiver Getting StartedGeneral LocationsFM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna Using the Standard Type Connector Not suppliedGetting Started Connecting the front speakersConnecting the rear and center speakers Connecting the Speakers16 ohm About the speaker impedanceIf your audio components have a Compu LINK-3 terminals Connecting Other ComponentsAudio component connections Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely On the front panel From the remote controlTurning the Power On and Off Standby Basic OperationsSelecting the Front Speakers From the remote control onlyAdjusting the Volume On the front panel onlyRecording a Source Listening with HeadphonesTo listen with only headphones Basic OperationsUsing the Sleep Timer Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessSelecting the Center Speaker Size Basic SettingsWhen the shut-off time comes To cancel the Sleep TimerOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Press TUNER/BAND so that the Control %/ Þ/ @ Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Receiving Radio BroadcastsWhat Information Can RDS Signals Provide? To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes Press PTY Search againDisplay gives you the PTY codes described on Press PTY Search while listening to an FM stationDescriptions of the PTY codes News Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode Traffic Announcement in your areaPress EON so that the program type TA/NEWS/INFO goes To stop listening to the program selected by EONTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn surround modes On JVC 3D Phonic modeOn the DAP mode Activating the Surround Sounds3DTHEATR Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DACTIONPress Effect to select the effect level Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode MarkGives clear vocal and the feeling of a concert hall Using the DAP ModesPavilion HallPress Rear +/- to adjust the rear speaker output level Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Select OFF in step DAP indicator goes off from the displayThis case Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode Speaker Arrangements for Surround Modes3CHLOGIC Preparing for Surround ModesTheater PrologicNormal Press Control @/ # to select the center modeDelay WideDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test again to stop the test tone Press Effect to adjust the effect levelPress Test to start checking the speaker output BalanceWork for selecting the surround/DAP/3D-PHONIC Modes Using Surround ModesTo cancel surround mode From the front panelSynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionOperating Other Components To operate JVC audio components using this remote controlStandby/On section Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsGeneral FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT

FM tuner (IHF)

AM (MW/LW) tuner

General