JVC RX-554RBK manual What Information Can RDS Signals Provide?

Page 23

English

About characters shown on the display

When the display shows PS, PTY, or RT signals, the following characters are used.

The display cannot differentiate upper case and lower case letters and always uses upper case letters.

The display cannot show accented letters, “A”, for instance, may stand for accented “A’s” like “Å, Ä, Ã, Á, À, and Â.”

A, Å, Ä,

K

U, Ü, Ú,

0

*

<

Ã, Á, À, Â

 

Ù, Û

 

 

 

 

 

 

B

L

V

1

+

>

 

 

 

 

 

C, C, C

M

W

2

-

=

 

 

 

 

 

D, D

N, Ñ

X

3

,

\

 

 

 

 

 

E, Ë, É,

O, Ö, Õ, Ô,

Y

4

.

'

È, Ê

Ò, Ó, Ø

 

 

 

 

 

 

 

F

P

Z, Z, Z

5

/

 

G

Q

 

6

 

 

 

 

 

 

H

R, R, R

 

7

 

 

 

 

I, Ï, Í, Ì, Î

S, S, S

 

8

 

 

 

 

 

 

 

J

T

 

9

 

 

What Information Can RDS Signals Provide?

You can see the RDS signals the station sends on the display.

To show the RDS signals

 

Press DISPLAY MODE while listening to an FM

DISPLAY MODE

station.

 

Each time you press the button, the display changes to show you the following information:

PS PTY RT Frequency

PS (Program Service):

While searching, “PS” appears and then the station names will be displayed. “NO PS” appears if no signal is sent.

PTY (Program Type):

While searching, “PTY” appears and then the type of the broadcast program will be displayed. “NO PTY” appears if no signal is sent.

RT (Radio Text):

While searching, “RT” appears and then text messages the station sends will be displayed. “NO RT” appears if no signal is sent.

Station Frequency:

Station frequency (non-RDS service)

When pressing DISPLAY on the remote control:

DISPLAY

 

Make sure that you have selected FM station using the remote control.

If not, the DISPLAY button does not work for tuner operation. (Pressing TUNER/BAND activates the remote control for tuner operation.)

Notes:

If searching finishes at once, “PS”, “PTY”, and “RT” will not appear on the display.

Even if you press DISPLAY MODE (or DISPLAY) while listening to an AM (MW/LW) station, the display only shows station frequency.

RDS is not available for AM (MW/LW) broadcasts.

18

Image 23
Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Front Panel Remote ControlParts Identification Handling the receiver Getting StartedGeneral LocationsFM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna Using the Standard Type Connector Not suppliedGetting Started Connecting the front speakersConnecting the rear and center speakers Connecting the Speakers16 ohm About the speaker impedanceIf your audio components have a Compu LINK-3 terminals Connecting Other ComponentsAudio component connections Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely On the front panel From the remote controlTurning the Power On and Off Standby Basic OperationsSelecting the Front Speakers From the remote control onlyAdjusting the Volume On the front panel onlyRecording a Source Listening with HeadphonesTo listen with only headphones Basic OperationsUsing the Sleep Timer Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessSelecting the Center Speaker Size Basic SettingsWhen the shut-off time comes To cancel the Sleep TimerOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsPress 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Press TUNER/BAND so that the Control %/ Þ/ @ Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Receiving Radio BroadcastsWhat Information Can RDS Signals Provide? To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes Press PTY Search againDisplay gives you the PTY codes described on Press PTY Search while listening to an FM stationDescriptions of the PTY codes News Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode Traffic Announcement in your areaPress EON so that the program type TA/NEWS/INFO goes To stop listening to the program selected by EONTo cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn surround modes On JVC 3D Phonic modeOn the DAP mode Activating the Surround Sounds3DTHEATR Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DACTIONPress Effect to select the effect level Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode MarkGives clear vocal and the feeling of a concert hall Using the DAP ModesPavilion HallPress Rear +/- to adjust the rear speaker output level Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Select OFF in step DAP indicator goes off from the displayThis case Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode Speaker Arrangements for Surround Modes3CHLOGIC Preparing for Surround ModesTheater PrologicNormal Press Control @/ # to select the center modeDelay WideDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test again to stop the test tone Press Effect to adjust the effect levelPress Test to start checking the speaker output BalanceWork for selecting the surround/DAP/3D-PHONIC Modes Using Surround ModesTo cancel surround mode From the front panelSynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionOperating Other Components To operate JVC audio components using this remote controlStandby/On section Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsGeneral FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT