JVC RX-554RBK manual Getting Started, Connecting the front speakers, Connecting the Speakers

Page 10

Getting Started

English

Connecting the Speakers

You can connect the following speakers:

Two sets of front speakers to produce normal stereo sound

One set of rear speakers to enjoy the surround effect

One center speaker to produce more effective surround effect (to make human voices outstanding)

For each speaker, connect one end of the speaker signal cable (not supplied) to the speaker terminal on the rear panel and the other end to the speaker.

1.Open each terminal.

2.Insert the end of the speaker signal cable as shown (be sure to remove the insulation at the end of each wire first).

3.Close the terminals to clamp the speaker signal cables firmly in place.

4.Connect the (–) and (+) terminals on the rear panel to the (–) and (+) terminals marked on the speakers.

Connecting the front speakers

Connect the front speakers to the FRONT SPEAKERS terminals.

CAUTION:

When connecting speakers, use speakers with the SAME IMPEDANCE indicated by the speaker terminals.

SPEAKERS 1

Left speaker

Right speaker

FRONT SPEAKERS

RIGHT

LEFT

1

1

2

2

SPEAKERS 2

 

 

 

 

 

 

 

Notes:

Connecting the rear and center speakers

 

When you connect rear

 

 

speakers, make sure that both

Connect the rear speakers to the REAR SPEAKERS terminals and the center speaker to

 

left and right speakers are

 

connected; otherwise, no

the CENTER SPEAKER terminals.

 

 

 

 

 

 

sound will come out of the

 

 

 

 

Center

Left rear

Right rear

 

rear speakers.

You can register the center

speaker

speaker

speaker

 

speaker size after you finish

LEFT

 

 

RIGHT

 

 

its connection. If you register

 

 

 

 

CENTER

REAR

 

 

it, you do not have to set the

 

 

center speaker mode while

SPEAKER

SPEAKERS

 

 

 

 

 

 

setting the surround mode. (If

 

 

 

 

you do not use a center

 

 

 

 

speaker, register that

 

 

 

 

information.) See page 13.

5

Image 10
Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Parts Identification Remote ControlFront Panel Locations Getting StartedGeneral Handling the receiverUsing the Standard Type Connector Not supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Getting StartedAbout the speaker impedance 16 ohmVideo component connections Connecting Other ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalsTo shut off the power completely Connecting the Power CordPutting Batteries in the Remote Control Basic Operations From the remote controlTurning the Power On and Off Standby On the front panelOn the front panel only From the remote control onlyAdjusting the Volume Selecting the Front SpeakersBasic Operations Listening with HeadphonesTo listen with only headphones Recording a SourceListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep TimerTo cancel the Sleep Timer Basic SettingsWhen the shut-off time comes Selecting the Center Speaker SizeTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Receiving Radio Broadcasts Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Press TUNER/BAND so that the Control %/ Þ/ @What Information Can RDS Signals Provide? Press PTY Search again To search for a program using the PTY codesSearching for a Program by PTY Codes To continue searching after the first stopPress PTY Search while listening to an FM station Display gives you the PTY codes described onDescriptions of the PTY codes Traffic Announcement in your area Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode NewsTo stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goesSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelActivating the Surround Sounds On JVC 3D Phonic modeOn the DAP mode On surround modes3DACTION Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DTHEATRMark Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Press Effect to select the effect levelHall Using the DAP ModesPavilion Gives clear vocal and the feeling of a concert hallSelect OFF in step DAP indicator goes off from the display Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Press Rear +/- to adjust the rear speaker output levelSpeaker Arrangements for Surround Modes Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode This casePrologic Preparing for Surround ModesTheater 3CHLOGICWide Press Control @/ # to select the center modeDelay NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayBalance Press Effect to adjust the effect levelPress Test to start checking the speaker output Press Test again to stop the test toneFrom the front panel Using Surround ModesTo cancel surround mode Work for selecting the surround/DAP/3D-PHONIC ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTo operate JVC audio components using this remote control Operating Other ComponentsOperating Other Components Standby/On sectionTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT