JVC RX-554RBK manual On the front panel only, From the remote control only, Adjusting the Volume

Page 15

Adjusting the Volume

On the front panel:

 

 

MASTER VOLUME

To increase the volume, turn MASTER VOLUME

 

 

clockwise.

+

 

 

To decrease the volume, turn it counterclockwise.

 

 

 

 

 

When you turn MASTER VOLUME rapidly, the volume

 

 

level also changes rapidly.

 

 

When you turn MASTER VOLUME slowly, the volume

 

 

level also changes slowly.

 

 

 

 

 

From the remote control:

To increase the volume, press VOLUME +.

To decrease the volume, press VOLUME –.

VOLUME

+

 

 

 

Selecting the Front Speakers

 

 

 

On the front panel only:

 

SPEAKERS

 

 

 

 

When you have connected two sets of front speakers, you

1

2

 

 

 

 

can select which to use. Pressing SPEAKERS 1 or

_ON ÑOFF

 

SPEAKERS 2 activiates the respective set of speakers.

 

To use the set of speakers connected to the FRONT SPEAKERS 1 terminals, press SPEAKERS 1 to set it in the _ON position, and press SPEAKERS 2 to set it in the Ñ OFF position.

To use the set of speakers connected to the FRONT SPEAKERS 2 terminals, press SPEAKERS 2 to set it in the _ON position, and press SPEAKERS 1 to set it in the Ñ OFF position.

To use both set of speakers, press both SPEAKERS 1 and 2 to set them in the _ON position.

To use neither set of speakers, press both SPEAKERS 1 and 2 to set them in the Ñ OFF position.

Muting the Sound

From the remote control only:

Press MUTING to turn off the sound through all

speakers and headphones connected.

MUTING

“MUTE” appears on the display and the volume turns off.

To restore the sound, press MUTING again.

Turning MASTER VOLUME or pressing VOLUME +/– also restores the sound.

English

CAUTION:

Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

Note:

The volume level can be adjusted within the range of “0” (minimum) to “62” (maximum).

Notes:

When only one set of the front speakers is connected to either the FRONT SPEAKERS 1 or 2 terminals, do not press both SPEAKERS 1 and 2 to set them in the _ON position. If you do, no sound comes out of the front speakers.

The SPEAKERS 1 and 2 do not affect the sound output of the center and rear speakers.

10

Image 15
Contents RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Remote Control Parts IdentificationFront Panel Handling the receiver Getting StartedGeneral LocationsFM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna Using the Standard Type Connector Not suppliedGetting Started Connecting the front speakersConnecting the rear and center speakers Connecting the Speakers16 ohm About the speaker impedanceIf your audio components have a Compu LINK-3 terminals Connecting Other ComponentsAudio component connections Video component connectionsConnecting the Power Cord To shut off the power completelyPutting Batteries in the Remote Control On the front panel From the remote controlTurning the Power On and Off Standby Basic OperationsSelecting the Front Speakers From the remote control onlyAdjusting the Volume On the front panel onlyRecording a Source Listening with HeadphonesTo listen with only headphones Basic OperationsUsing the Sleep Timer Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessSelecting the Center Speaker Size Basic SettingsWhen the shut-off time comes To cancel the Sleep TimerOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsTo cancel a stored preset station To tune in a preset stationPress 10 keys to select a preset channel number Press TUNER/BAND so that the Control %/ Þ/ @ Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Receiving Radio BroadcastsWhat Information Can RDS Signals Provide? To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes Press PTY Search againDisplay gives you the PTY codes described on Press PTY Search while listening to an FM stationDescriptions of the PTY codes News Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode Traffic Announcement in your areaPress EON so that the program type TA/NEWS/INFO goes To stop listening to the program selected by EONUsing the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn surround modes On JVC 3D Phonic modeOn the DAP mode Activating the Surround Sounds3DTHEATR Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DACTIONPress Effect to select the effect level Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode MarkGives clear vocal and the feeling of a concert hall Using the DAP ModesPavilion HallPress Rear +/- to adjust the rear speaker output level Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Select OFF in step DAP indicator goes off from the displayThis case Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode Speaker Arrangements for Surround Modes3CHLOGIC Preparing for Surround ModesTheater PrologicNormal Press Control @/ # to select the center modeDelay WideDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test again to stop the test tone Press Effect to adjust the effect levelPress Test to start checking the speaker output BalanceWork for selecting the surround/DAP/3D-PHONIC Modes Using Surround ModesTo cancel surround mode From the front panelSynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionOperating Other Components To operate JVC audio components using this remote controlStandby/On section Operating Other ComponentsProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT