Lucent Technologies 20 manual Configuring LAN interface in bridging mode

Page 33

Configuring a 20 Series CellPipe

Configuring LAN interface

AS0_Dn_Latency_Actual <interleave>

LS0_Up_Bytes_Actual 0

LS0_Up_Latency_Actual <interleave>

Fast_R_Up_Actual0

Interleave_S_Up_Actual 0

Interleave_D_Up_Actual 0

Interleave_R_Up_Actual 0

Fast_R_Dn_Actual0

Interleave_S_Dn_Actual 0

Interleave_D_Dn_Actual 0

Interleave_R_Dn_Actual 0

Select the stnl command to configure the local ADSL coding type.

>adsl> stnl - <T1.413><g.Lite><g.Dmt><Multi-Mode>

Select the trellis command to enable or disable Trellis encoding.

>adsl> trellis <Enable><Disable>

Select the tx_pwr command to configure the transmitted power attentuation for a range between 0 dB and 12 dB.

>adsl> tx_pwr <0> .. <12>

Select the tx_bin command to allow the user to limit bins used for special configuration in the transmitted signal.

>adsl> tx_bin - <start_bin> <end_bin>

Configuring LAN interface

This section provides menus for configuring the LAN interface in both bridging and routing mode.

Configuring LAN interface in bridging mode

The following is a list of the menus available under the lan command in bridging mode:

CellPipe™ 20 Series User’s Guide

4-7

Image 33

Contents CellPipe 20 Series Lucent Technologies Customer Service Customer ServiceFinding information and software Obtaining technical assistanceCustomer Service Contents Upgrading System Software About this guide IntroductionWhat is the CellPipe 20 Series Product Family? What is the CellPipe 20 Series Product Family?Lucent TURN-UP CellPipe 20 Series managementLucent TURN-UP Page Verifying package contents SetupItems you need for installation Connecting CellPipe 20 Series productsItems you need for installation CellPipe 20 Series rear panels Connecting CellPipe 20 Series productsConsole setup Checking status lightsChecking status lights Console setup Page Syntax of command-line interface Command-Line InterfaceDisplaying information about a command Using the commandsUsing the commands Viewing the main menuDisplaying second-level commands Bridging commandsSaving configurations Bridging commandsMain menu Second-level menus/description Set all configuration to factory setting Routing commands Routing commandsAdditional main-menu and second-level routing commands Command-Line Interface Command-Line Interface Page Auto-provisioning Configuring a 20 Series CellPipeConfiguring WAN interface Sdsl commands and configurationsConfiguring WAN interface Select the dbit command to configure the sdsl data bit Adsl commands and configurations Select the abort command to abort the Adsl connection Multimode Configuring LAN interface Configuring LAN interface in bridging modeConfiguring LAN interface Configuring LAN interface in routing mode Configuring the manage command Configuring the mode commandConfiguring the manage command Quick command in bridging mode Configuring the quick commandQuick command in routing mode Configuring the quick commandConfiguring the r1483 command R1483 command in bridging modeConfiguring the r1483 command R1483 command in routing mode Configuring the dnsrelay command Configuring the ipoa commandConfiguring the dnsrelay command Configuring the pppoa command Configuring the pppoa commandConfiguring the pat command Configuring the pat commandSelect the show command to display the Pat configuration Preparing to upgrade Upgrading System SoftwareObtaining software Upgrading software Upgrading softwareWarranties and FCC Regulations Product warrantyOut-of warranty repair Warranty repairFCC Part 15 Notice FCC Part 15 NoticeIC CS-03 Notice IC CS-03 Notice