Lucent Technologies 20 manual FCC Part 15 Notice, Warranty repair, Out-of warranty repair

Page 46

Warranties and FCC Regulations

FCC Part 15 Notice

BUSINESS RELATIONS. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES.

Warranty repair

1During the first three (3) months of ownership, Lucent Technologies will repair or replace a defective product covered under warranty within twenty-four (24) hours of receipt of the product. During the fourth (4th) through twelfth (12th) months of ownership, Lucent Technologies will repair or replace a defective product covered under warranty within ten (10) days of receipt of the product. The warranty period for the replaced product shall be ninety (90) days or the remainder of the warranty period of the original unit, whichever is greater. Lucent Technologies will ship surface freight. Expedited freight is at customer’s expense.

2The customer must return the defective product to Lucent Technologies within fourteen (14) days after the request for replacement. If the defective product is not returned within this time period, Lucent Technologies will bill the customer for the product at list price.

Out-of warranty repair

Lucent Technologies will either repair or, at its option, replace a defective product not covered under warranty within ten (10) working days of its receipt. Repair charges are available from the Repair Facility upon request. The warranty on a serviced product is thirty (30) days measured from date of service. Out-of-warranty repair charges are based upon the prices in effect at the time of return.

FCC Part 15 Notice

!Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is unlikely to cause harmful

A-2

CellPipe™ 20 Series User’s Guide

Page 45 Page 47
Image 46
Page 45 Page 47
Contents CellPipe 20 Series Lucent Technologies Finding information and software Customer ServiceCustomer Service Obtaining technical assistanceCustomer Service Contents Upgrading System Software Introduction About this guideWhat is the CellPipe 20 Series Product Family? What is the CellPipe 20 Series Product Family?CellPipe 20 Series management Lucent TURN-UPLucent TURN-UP Page Setup Verifying package contentsConnecting CellPipe 20 Series products Items you need for installationItems you need for installation Connecting CellPipe 20 Series products CellPipe 20 Series rear panelsChecking status lights Console setupChecking status lights Console setup Page Command-Line Interface Syntax of command-line interfaceUsing the commands Using the commandsDisplaying information about a command Viewing the main menuSaving configurations Bridging commandsDisplaying second-level commands Bridging commandsMain menu Second-level menus/description Set all configuration to factory setting Routing commands Routing commandsAdditional main-menu and second-level routing commands Command-Line Interface Command-Line Interface Page Configuring a 20 Series CellPipe Auto-provisioningSdsl commands and configurations Configuring WAN interfaceConfiguring WAN interface Select the dbit command to configure the sdsl data bit Adsl commands and configurations Select the abort command to abort the Adsl connection Multimode Configuring LAN interface in bridging mode Configuring LAN interfaceConfiguring LAN interface Configuring LAN interface in routing mode Configuring the mode command Configuring the manage commandConfiguring the manage command Quick command in routing mode Configuring the quick commandQuick command in bridging mode Configuring the quick commandR1483 command in bridging mode Configuring the r1483 commandConfiguring the r1483 command R1483 command in routing mode Configuring the ipoa command Configuring the dnsrelay commandConfiguring the dnsrelay command Configuring the pppoa command Configuring the pppoa commandConfiguring the pat command Configuring the pat commandSelect the show command to display the Pat configuration Upgrading System Software Preparing to upgradeObtaining software Upgrading software Upgrading softwareProduct warranty Warranties and FCC RegulationsFCC Part 15 Notice Warranty repairOut-of warranty repair FCC Part 15 NoticeIC CS-03 Notice IC CS-03 Notice
Top Page Image Contents