Lucent Technologies 20 manual Configuring the pppoa command

Page 40

Configuring a 20 Series CellPipe

Configuring the pppoa command

Select the setqos command to set the class for quality of service.

>ipoa> setqos [<vpi>/]<vci> <ubrcbrvbr(nrt)>

Select the setrip command to set the PVC for RIP.

>ipoa> setrip [<vpi>/]<vci> <121&20>

Select the setwanip command to set up to eight PVCs, the WAN IP addresses for each PVC, and the gateway IP address.

>ipoa> setwanip [<vpi>/]<vci> <wanip[/<masknum>]> <gatewayip>

Select the show command to display the IPoA configuration.

> ipoa> show

IPoA setting:

FUNCTION VPI/VCI CLASS Wan IP/MaskNum GatewayIP RIP

Configuring the pppoa command

The following is a list of the menus available under the pppoa command:

adduser

- add user ID

and password

chpass

- change user

password

deluser

- delete user

 

echo

- set echo interval time

setllc

- add LLC header on the packets

setqos

- set class

 

setrip

- set RIP configuration

show

- show PPPoA configuration

Select the adduser command to set up a PVC, user ID, and select an authentication protocol for a user.

>pppoa> adduser [<vpi>/]<vci> <userid> [<chappap>]

Select the chpass command to change the password for the user of a pppoa connection.

>pppoa> chpass

Old Password:******

New Password:******

4-14

CellPipe™ 20 Series User’s Guide

Image 40
Contents CellPipe 20 Series Lucent Technologies Customer Service Customer ServiceFinding information and software Obtaining technical assistanceCustomer Service Contents Upgrading System Software Introduction About this guideWhat is the CellPipe 20 Series Product Family? What is the CellPipe 20 Series Product Family?CellPipe 20 Series management Lucent TURN-UPLucent TURN-UP Page Setup Verifying package contentsConnecting CellPipe 20 Series products Items you need for installationItems you need for installation Connecting CellPipe 20 Series products CellPipe 20 Series rear panelsChecking status lights Console setupChecking status lights Console setup Page Command-Line Interface Syntax of command-line interfaceUsing the commands Displaying information about a commandUsing the commands Viewing the main menuBridging commands Displaying second-level commandsSaving configurations Bridging commandsMain menu Second-level menus/description Set all configuration to factory setting Routing commands Routing commandsAdditional main-menu and second-level routing commands Command-Line Interface Command-Line Interface Page Configuring a 20 Series CellPipe Auto-provisioningSdsl commands and configurations Configuring WAN interfaceConfiguring WAN interface Select the dbit command to configure the sdsl data bit Adsl commands and configurations Select the abort command to abort the Adsl connection Multimode Configuring LAN interface in bridging mode Configuring LAN interfaceConfiguring LAN interface Configuring LAN interface in routing mode Configuring the mode command Configuring the manage commandConfiguring the manage command Configuring the quick command Quick command in bridging modeQuick command in routing mode Configuring the quick commandR1483 command in bridging mode Configuring the r1483 commandConfiguring the r1483 command R1483 command in routing mode Configuring the ipoa command Configuring the dnsrelay commandConfiguring the dnsrelay command Configuring the pppoa command Configuring the pppoa commandConfiguring the pat command Configuring the pat commandSelect the show command to display the Pat configuration Upgrading System Software Preparing to upgradeObtaining software Upgrading software Upgrading softwareProduct warranty Warranties and FCC RegulationsWarranty repair Out-of warranty repairFCC Part 15 Notice FCC Part 15 NoticeIC CS-03 Notice IC CS-03 Notice