Polycom 8002 manual Security

Page 31

SpectraLink 8002 Wireless Telephone Configuration

Security

*NONE disables any 802.11 encryption or security authentication mechanisms.

For WEP, WPA-PSK and WPA2-PSK set each of the following options to match exactly the settings in the APs.

The encryption key or encryption passphrase displays as it is entered. For security reasons codes will not display again once entered, even if the entry screen is revisited.

WEP (Wired Equivalent Privacy) is a wireless encryption protocol that encrypts data frames on the wireless medium allowing for greater security in the wireless network. If WEP is required at this site, you must configure each handset to correspond with the encryption protocol set up in the APs. Select the entries from the options below to enable the handset to acquire the system.

Authentication Select either Open System or Shared Key.

WEP On/Off Select either WEP Off or WEP On.

Key Information

Default Key Enter the key number specified for use by the handsets. This will be 1 through 4.

Key Length Select either 40-bitor 128-bitdepending on the key length specified for use at this location.

Key 1 through 4 Scroll to the key option that corresponds to the Default Key that was entered above. Enter the encryption key as a sequence of hexadecimal characters. (Use the 2 and 3 keys to access hexadecimal digits A-F, use the Right Arrow key to advance to the next digit, and the Left Arrow key to backspace.) For 40-bit keys, enter 10 hex characters. For 128-bit keys, enter 26 hex characters. The display will scroll as needed.

Rotation Secret This is used for proprietary WEP key rotation. Refer to your custom document if this feature is supported in your system.

WPA-PSKThe security features of WPA (Wi-Fi Protected Access) using PSK (pre-shared key) are available and may be used if supported by the APs in the facility. Select either Passphrase and enter a passphrase between eight and 63 characters in length or Pre-shared Key and enter the 256-bit key code.

PN: 1725-36034-001_C.doc

31

Image 31
Contents Administration Guide Contact Information Trademark InformationPatent Information Copyright NoticeKnowledge base to assist troubleshooting is available at Essential Installation PointersYou must update the software with the most recent code Data APs may not support VoWiFiPage Polycom Model Numbers About this GuideRelated Documents Icons and Conventions Customer Support HotlineContents Software License and Protocol Management Programming the SIP Handset FeaturesUsing the SIP Handset Testing a Handset Diagnostic ToolsIndex Page WMM-Compatible Access Points SpectraLink Wireless Telephone OverviewSecurity Options Quick Start Guide Security Regulatory Domain Preferred Channels SIP Servers System DiagramSystem Components SpectraLink 8002 Wireless TelephoneAccess points Ethernet switchSIP Tftp server SIP serverSIP phone Tftp serverDHCP, Tftp Handset SpecificationsWMM WPA2-PSKXxxxx Startup SequenceIcon Icons shown in bold turns off when EXTPN 1725-36034-001C.doc SpectraLink 8002 Wireless Telephone Configuration Alphanumeric string entry Admin Administration MenuOpening the Admin menu Entering and editing Admin menu optionsTo Enter Press WEP Admin menuAdmin Menu Items 2nd Level 3rd Level 4th Level 5th Level ESS IDAdmin Menu Items 2nd Level 3rd Level 4th Level 5th Level License Option Phone ConfigSIP Registration IP Address Network ConfigAdmin Password OAI On/OffOption Meaning SpectraLink 8002 Wireless Telephone Configuration Essid Security Regulatory Domain Transmit PowerRestore Defaults DiagnosticsStandby mode, options menu User-defined Preferences Standby MenuStandby Menu Items 2nd Level 3rd Level 4th Level Standby menuPBX PN 1725-36034-001C.doc Ring Options Lock KeysTelephone Ring Phone Options Firmware Version System InfoPhone IP Addr Server IP AddrPage Requirements Software License and Protocol ManagementConfiguration Process Software License and Protocol Management Page SIP Tftp Server Configuration Files Programming the SIP Handset FeaturesGuidelines Handset-specific files e.g. sip3001.cfg Generic file sipallusers.cfgParameter Value Description Proxy server commandsSER Parameter Value Description Codecs AuthFavorite SIPallusers.cfg Sample Configuration Files# PROXY1MAILACCESS = PROXY1KEEPALIVESECS=14 #PROXY1ADDR #PROXY2ADDR Sample handset-specific fileLINE1 LINE2CALLID Overview Using the SIP HandsetLine indicators Handset DisplayHandset icons Signal strengthBattery charge Indicator FunctionDownload Standby mode on-hookActive mode off-hook Handset modesSoftkeys Messaging modeSoftkey Name Displayed… Press to… Using the SIP Handset Line menu MenusFavorites menu Menu display FCN menuIf you want to… Then… Feature activationHandset Operation Alphanumeric dialingLine 1 your dial number To dialed number Hold Rej Mute Line 1 your dial number Fr caller ID Answ Rej =Fr caller ID Rsme Mute End If you want to… Then… Using the SIP Handset Page Testing a Handset Page Site Survey Diagnostic ToolsDisplay has the following layout for single Essid mode M T Solving coverage issues Diagnostics ModeM m m c h s s a i d M m c h s s m n e m E m ScreenC o u N n n A s U n t Syslog Mode AP MAC Message type ErrorsEvents Full MACCall Start Call type telephony, OAI, PTT Messages are formatted like the following example Conducting a site survey Certifying the InstallationPN 1725-36034-001C.doc Message Description Software MaintenanceUpgrading handsets Normal download messagesTftp Download failure or recovery messagesCapacity TroubleshootingAccess point problems Range/out-of-rangeTransmission obstructions Configuration problemsMessage Description Action Handset Status MessagesMessage Description Action Troubleshooting OFF Do not PowerLicense Option set DhcpCRC Message Description Action Page Countries Max. Power Limit peak powerAppendix a Regulatory Domains Domain Band Channels Identifier 4000 2.4745 MHzPN 1725-36034-001C.doc Coverage Coverage test Index