NordicTrack CTL8250, CTL8750, CTL8500 Turning the Walking Platform, Remove the key and unplug

Page 31

TURNING THE WALKING PLATFORM

Both sides of the walking platform are designed to be used as walking surfaces. Inspect the walking platform peri- odically for wear. If there is any wood showing through the phenolic coating, or if the surface is damaged, the walking platform should be turned over. The walking platform will need to be turned over after every 6,000 to 7,500 miles. Follow the instructions below to turn over the walking platform.

1.Remove the key and unplug the

power	cord.	Remove the two
Hood	Screws	(2) and lift off the

Motor Hood (1). Next, remove the two Rear Roller Bolts (82), the two Roller Guard Screws (80), and the Right and Left Roller Guards (81, 83).

2. Remove the six Platform Screws

(6). Lift the Rear Roller (79) and slide it out of the Walking Belt

(71). Lift the Walking Platform

(70)a few inches, slide it out of the Walking Belt, turn it over, and then slide it back into the Walking Belt. Slide the Rear Roller back into the Walking Belt. Reattach

the six Platform Screws (6).

1–3		1	2
		1	2
	80		6
83	6		6
83	6
82			70
		80	70
		80
	81	6
	82
	71
	79

3.Reattach the Right and Left Roller Guards (81, 83) with the two Roller Guard Screws (80). Insert the Rear Roller Bolts (82) into the Roller Guards and thread them into the Rear Roller (79). Reattach the Motor Hood

(1)with the two Hood Screws (2).

4.Next, the Walking Belt (71) will need to be adjusted to the proper tension. Using chalk, make two marks on the

Walking Belt exactly 50” apart, as shown in the drawing. Tighten both Rear Roller Bolts (82) until the two chalk marks move apart an additional 3/16” to 1/4”. Make sure to keep the Walking Belt centered.

REPLACING THE WALKING PLATFORM

4	71
	71
	50”
82

When both sides of the walking platform become worn, the walking platform should be replaced. The walking
platform will need to be replaced after every 12,000 to 15,000 miles. Refe		r to page 44 to order	a new walking plat-
form. Follow the instructions above to replace the walking platform.
REPLACING THE WALKING BELT
When the walking belt becomes worn, it should be replaced. The walking belt will need to be replaced after every
12,000 to 15,000 miles. Refe	r to page 44 to order a new walking belt.

30

Image 31

Contents Mon.-Fri., 6 a.m.-6 p.m. MST Serial Number DecalSection How to Connect your CD Player to the TreadmillSix-month Preventive Maintenance Record OntentsPage Use an extension cord PrecautionsUse the treadmill only as described in this manual Wear appropriate exercise clothes whenNever insert or drop any object into any opening Before servicing Ecal PlacementDisconnect power ArningFor your benefit, read this manual carefully before Efore YOUHOW to Readmill Is eliminated Firmly tighten all eightUpright Bolts Firmly tighten the four Handrail BoltsHandrails Lift HOW to OVEDue to the size and weight of the treadmill, mov Before moving the treadmill, make sure thatEquipment-grounding conductor can HOW to OnnectHOW to Connect a Catv Cable Improper connectionHead Audio Cable Phones HOW to Onnect Your Player toHOW to Connect Your Portable CD Player If your treadmill has the Basic console orOr call Ground Zero toll-free at HOW to Pgrade YourMatrix Main Display HOW to AsicFeatures of the Console Grams that adjust the speed and inclineGetting Started Select the manual mode HOW to USE the Manual ModeChange the incline of the treadmill as desired Avoid Moving your Hands Pulse/% MaxMeasure your heart rate if desired StandSelect one of the six preset programs HOW to USE Preset ProgramsSpeed + button. The walking belt will begin to Restart the program, press the StartMent Whenkey.the program is completed, removeSelect one of the three pulse-driven programs HOW to USE PULSE-DRIVEN ProgramsEnter a target heart rate setting Chest pulse sensorEnter your age Your must enter your age to use the fitness HOW to USE the Fitness Test Program8Whenkey.the program is completed, remove Select the fitness test programFitness test program will con Cally increaseRent four-minute level is completed Ten fitness levels fitness levelFor speed To the next settings of the CD programPress the Play button on your CD player Treadmill is about to changePress the Enter AGE/WT button again HOW to USE the Maintenance ModeHold down the Enter AGE/WT button Press the Enter AGE/WT button to viewIf you are using a cable TV connection, press the + Button until the words Safety KEY Disabled appearPress the Enter AGE/WT button four times To exit the maintenance mode at any time, holdHOW to Reset the Service Distance Hold down the Reset button and the +Compatible chest pulse sensor not included That adjust the speed and incline Treadmill toFlat Screen Television Matrix Main Display Addi Jack HOW to USE the Workout TV Console Put on headphones not included if desired Adjust the volumeRemove it Touchscreen Main Display HOW toAddition, you can use the console’s touchscreen to go Monthly Maintenance Weekly MaintenancePreventive Remove the key and unplug Turning the Walking PlatformReplacing the Walking Platform Motor belt CleanCheck Tighten all TreadmillPreventive Walking platform Symptom the Power does not Turn onSymptom the Power Turns OFF During USE AdjustmentRepeat until the walking belt is properly tightened Symptom the Walking Belt is OFF-CENTEREstablish personal fitness goals XerciseFactors in a Sensible Diet Exercise StepsHamstring Stretch Weight Loss TipsWarm up before you begin Toe Touch StretchParticipate in strength training Benefits of Aerobic ExerciseGet FIT with NordicTrack Stretch again at the end of your exercise 8sessionWorkout Programs Workout TipsImited Arranty State Laws Receipt of Parts and ServiceExclusive Warranty Unauthorized Changes to WarrantyDescription Part131 124 122 125 127 106 107 105 104 OS. C TL82500, C TL85000, C116 112 120 113 111 108116 R0901A 115 110Parts HOW to Rder Eplacement