4. SYMPTOM: THE WALKING BELT IS
a. If the walking belt has shifted to the left: Remove the |
|
|
|
|
|
key and unplug the power cord. Using the included allen |
| a |
|
|
|
wrench, turn the roller adjustment bolts in the directions |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| |
shown, 1/4 of a turn each. Be careful not to overtighten the |
|
|
|
|
|
|
|
|
|
| |
walking belt. Plug in the power cord, insert the key and |
|
|
|
|
|
use the INCLINE TRAINER for a few minutes. Repeat until |
|
|
|
|
|
the walking belt is centered. |
|
|
|
|
|
|
|
|
|
|
|
b. If the walking belt has shifted to the right: Remove the key and unplug the power cord. Using the included allen wrench, turn the roller adjustment bolts in the directions shown, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and use the INCLINE TRAINER for a few minutes. Repeat until the walking belt is centered.
b |
c. If the walking belt slips when walked on: Remove the |
|
|
|
|
|
|
|
|
|
| |
| c |
|
|
| |
key and unplug the power cord. Using the included allen |
|
|
|
| |
wrench, turn both roller adjustment bolts clockwise 1/4 of a |
|
|
|
|
|
|
|
|
|
| |
turn. When the walking belt is properly tightened, you |
|
|
|
|
|
|
|
|
|
| |
should be able to lift each side of the walking belt 1 to 2 |
|
|
|
|
|
inches off the walking platform. The center of the walking |
|
|
|
|
|
belt should just touch the walking platform. Make sure to |
|
|
|
|
|
keep the walking belt centered. Plug in the power cord, in- |
|
|
|
|
|
sert the key and run the INCLINE TRAINER for a few min- |
|
|
|
|
|
utes. Repeat until the walking belt is properly tightened. |
|
|
|
|
|
Note: As you tighten the roller adjustment bolts, the front |
|
|
|
|
|
roller will move. If the front roller stops moving, do not |
|
|
|
|
|
|
|
|
|
| |
further tighten the roller adjustment bolts; contact |
|
|
|
|
|
your distributor. |
|
|
|
|
|
5.SYMPTOM: THE WALKING BELT STOPS OR THE INCLINE CANNOT BE ADJUSTED EVEN THOUGH THE CONSOLE REMAINS LIT
a.This indicates that a controller error may have occurred. To correct the problem, refer to step 8 on page 22.
6.SYMPTOM: THE INCLINE SYSTEM DOES NOT FUNCTION PROPERLY OR THE INCLINE SYSTEM DOES NOT APPEAR TO BE AT THE INCLINE LEVEL SHOWN IN THE MAIN DISPLAY
a.The incline system may need to be calibrated. To initiate the calibration routine, hold down the SPEED + button and the SPEED – button simultaneously for three seconds. During the calibration routine, the INCLINE TRAINER will automatically travel to the lowest incline level and then return to level.
b.If the incline system still does not function properly, contact your distributor.
7.SYMPTOM: THE WORDS LUBRICATE DECK APPEAR EVERY FEW MINUTES IN THE MAIN DISPLAY
a.If the words LUBRICATE DECK appear in the main display, the walking platform should be checked for ade- quate lubricant. Follow the instructions in step 4 on page 27 to lubricate the walking platform if necessary. After you have lubricated the walking platform, refer to HOW TO RESET THE LUBE REMINDER on page 24.
If this is not done, the words LUBRICATE DECK will continue to appear.
32