Precor M9.33 manual Adjusting the Running Belt

Page 48

5.Press the SPEED ▲ key until the display shows a speed of 3 mph (5 kph).

CAUTION: If you hear any chafing or the running belt appears to be getting damaged, stop the running belt immediately by pressing the red STOP button. Contact Precor Customer Support.

6.Walk around to the rear of the unit and observe the belt for a few minutes. The belt should be centered on the running belt. If the belt drifts off center, you must make adjustments.

Important: If the belt needs alignment, make the adjustments at once. Failure to align the belt may cause the belt to tear or fray, which is not covered by the Precor Limited Warranty.

7.To stop the running belt, press the red STOP button.

8.Turn the treadmill OFF.

Adjusting the Running Belt

If you are unsure about adjusting the running belt, call Precor Customer Support (refer to Obtaining Service).

CAUTION: To ensure your safety, use the I/O power switch to turn OFF the treadmill before making any adjustments. Do not adjust the running belt when someone is standing on the unit.

1.Locate the right belt adjustment bolt in the rear end cap of the treadmill. Refer to Diagram 11.

Diagram 11: Adjusting belt location

To determine left and right, stand at the rear of the treadmill and face the display. Make all belt adjustments on the right rear corner bolt using the hex key provided.

Owner’s Manual: Maintenance

46

Image 48
Contents Page Page Important Safety Instructions Grounding Instructions Password Security Safety ApprovalGrounding Instructions Radio Frequency Interference RFI Units Designated for U.S. MarketsFederal Communications Commission, Part European Applications Canadian Department of CommunicationsDébranchez avant de réparer Obtaining Service Table of Contents Precor Residential Equipment Using the Security Clip Entering the PasswordUsing the Handrails Turning the Unit on and OFF114 GuidelinesUsing the Heart Rate Touch-Sensitive Grips Using SmartRate Exercise to Your Target Heart Rate LEDDisplay Console Page Scanning and the Display KeypadQuickstart Changing the Display Features Using the Select Key 1532 Precor Choosing Quickstart User Selecting a User IDSelecting a Program CST2Cooling Down After a Workout Pausing During a Workout or the Cool-Down Period Ending a Workout Programs Choosing a ProgramProgram Tips Table below shows a variety of program optionsManl Manual Manl Program Walk WLK ProgramsIntv Run RUN Programs Interval Intv ProgramRand Random Rand ProgramWeight Loss Wtls Program WtlsHeart Rate Control HRC Program Warm-up PeriodUsing the HRC Program Custom CST1 or CST2 ProgramsClearing the Settings on a Custom Program Advanced Programming and Troubleshooting Advanced Programming TipsRESET, QUICKSTART, ENTER, Select User 2, Incline Selecting a U.S. Standard or Metric DisplaySelecting Password Protection Informational Displays Viewing the OdometerViewing the Hour Meter Viewing the Software Version and Part NumbersViewing the Error Log ER33 AT 12,345,678 Miles 1,714 HoursTroubleshooting Error Codes Viewing the Serial NumberTroubleshooting Heart Rate RcvrCleaning the Equipment InspectionStoring the Chest Strap Checking the Alignment Running BeltAdjusting the Running Belt Servicing the Treadmill Long-Term StorageLimited Warranty Warranty Periods and CoverageOptions / Accessories This limited warranty shall not apply to Conditions and RestrictionsDisclaimer and Release Exclusive Remedies Exclusion of Consequential and Incidental DamagesThank You and Welcome to Precor Tell US about Your NEW Precor Product Page Product Specifications M9.33 Low Impact TreadmillQUICKSTARTiTM Choose a Program Assembly Guide Required Tools Hardware Kit Assembly Steps Incline , Speed , Speed M9.3x Low-Impact Treadmills Assembly Guide Checking the Alignment and Adjusting the Running Belt Precor Incorporated 20031 142nd Avenue NE Box