Precor M9.33 manual ER33 AT 12,345,678 Miles 1,714 Hours, Viewing the Error Log

Page 43

6.When you are ready, press ENTER to move to the next display (error log).

Viewing the Error Log

ERROR LOG appears on the display followed by the first entry in the error log if there are any errors. Up to ten error codes can be retrieved.

If there are no errors in the log, you will see NO ERRORS displayed.

7.To view any additional error codes in the error log, use the arrow keys. Each error code specifies when it occurred, listing the odometer and hour meter values. Refer to Diagram 10.

Most recent error

The hour meter at the time

 

the error was detected.

1: ER33 AT 12,345,678 MILES 1,714 HOURS

Error code

Odometer reading at the

 

time the error occurred.

Diagram 10: Error log

 

8.Copy the error code information to paper so you can provide it to Customer Support if needed. Be sure to copy it exactly as shown.

9.When you no longer need the information in the error log, press QUICKSTART to erase the error log. While the error log is displayed, maintain light pressure on the QUICKSTART key until CLEAR, and then OK appears.

Important: You cannot retrieve the error log once you have cleared it. You may want to resolve any issues you are experiencing with the treadmill before clearing the error log.

10.When you are ready, press ENTER to move to the next display (serial number).

Owner’s Manual: Advanced Programming and Troubleshooting

41

Image 43
Contents Page Page Important Safety Instructions Grounding Instructions Safety Approval Password SecurityGrounding Instructions Units Designated for U.S. Markets Radio Frequency Interference RFIFederal Communications Commission, Part Canadian Department of Communications European ApplicationsDébranchez avant de réparer Obtaining Service Table of Contents Precor Residential Equipment Entering the Password Using the Security ClipTurning the Unit on and OFF Using the HandrailsGuidelines 114Using the Heart Rate Touch-Sensitive Grips Using SmartRate LED Exercise to Your Target Heart RateDisplay Console Page Keypad Scanning and the DisplayQuickstart Changing the Display Features Using the Select Key 1532 Precor Choosing Quickstart Selecting a User ID UserCST2 Selecting a ProgramCooling Down After a Workout Pausing During a Workout or the Cool-Down Period Ending a Workout Choosing a Program ProgramsTable below shows a variety of program options Program TipsManual Manl Program Walk WLK Programs ManlRun RUN Programs Interval Intv Program IntvRandom Rand Program RandWtls Weight Loss Wtls ProgramWarm-up Period Heart Rate Control HRC ProgramCustom CST1 or CST2 Programs Using the HRC ProgramClearing the Settings on a Custom Program Advanced Programming Tips Advanced Programming and TroubleshootingSelecting a U.S. Standard or Metric Display RESET, QUICKSTART, ENTER, Select User 2, InclineSelecting Password Protection Viewing the Software Version and Part Numbers Informational DisplaysViewing the Odometer Viewing the Hour MeterER33 AT 12,345,678 Miles 1,714 Hours Viewing the Error LogViewing the Serial Number Troubleshooting Error CodesRcvr Troubleshooting Heart RateInspection Cleaning the EquipmentChecking the Alignment Running Belt Storing the Chest StrapAdjusting the Running Belt Long-Term Storage Servicing the TreadmillWarranty Periods and Coverage Limited WarrantyOptions / Accessories Conditions and Restrictions This limited warranty shall not apply toDisclaimer and Release Exclusion of Consequential and Incidental Damages Exclusive RemediesThank You and Welcome to Precor Tell US about Your NEW Precor Product Page M9.33 Low Impact Treadmill Product SpecificationsQUICKSTARTiTM Choose a Program Assembly Guide Required Tools Hardware Kit Assembly Steps Incline , Speed , Speed M9.3x Low-Impact Treadmills Assembly Guide Checking the Alignment and Adjusting the Running Belt Precor Incorporated 20031 142nd Avenue NE Box