Precor M9.33 manual Incline , Speed , Speed

Page 63

To install the handrail, raise the incline.

CAUTION: Do not stand on the treadmill while raising the incline.

a.Plug the treadmill into a power outlet. Locate the I/O power switch on the front panel and turn the unit ON.

b.Stand beside the treadmill and press QUICKSTART. If you are prompted for a password, press

INCLINE ▼, SPEED ▼, SPEED ▲.

c.When the running belt begins moving, press the INCLINE ▲ key until the display shows an incline of 15.

d.When the lift stops moving, press the red STOP button, and then turn the treadmill OFF.

Use the ¼-inch hex key to remove the four handrail clamp screws. Set the lower handrail clamp and fasteners aside.

Slide the ends of the handrails toward the center handrail clamp and secure them to each side bracket using two socket head screws (C) and two washers (F). Finger tighten.

Attach the lower portion of the handrails to the side rails using four socket head screws (C) and four washers (D). Finger tighten.

Note: To complete the M9.31 assembly, skip steps 11 and 12 and continue with step 13.

On the M9.35 and M9.33, heart rate cables protrude from the ends of both handrails. Slide the end of each cable into its receptacle. Place excess cable inside the handrail clamp.

Important: The cable receptacles mirror the connectors so that they cannot be improperly installed. Do not force a connection! Take time and look for the tabs on the connectors.

M9.3x Low-Impact Treadmills Assembly Guide

5

Image 63

Contents Page Page Important Safety Instructions Grounding Instructions Password Security Safety ApprovalGrounding Instructions Radio Frequency Interference RFI Units Designated for U.S. MarketsFederal Communications Commission, Part European Applications Canadian Department of CommunicationsDébranchez avant de réparer Obtaining Service Table of Contents Precor Residential Equipment Entering the Password Using the Security ClipTurning the Unit on and OFF Using the HandrailsGuidelines 114Using the Heart Rate Touch-Sensitive Grips Using SmartRate LED Exercise to Your Target Heart RateDisplay Console Page Keypad Scanning and the DisplayQuickstart Changing the Display Features Using the Select Key 1532 Precor Choosing Quickstart Selecting a User ID UserCST2 Selecting a ProgramCooling Down After a Workout Pausing During a Workout or the Cool-Down Period Ending a Workout Choosing a Program ProgramsTable below shows a variety of program options Program TipsManual Manl Program Walk WLK Programs ManlRun RUN Programs Interval Intv Program IntvRandom Rand Program RandWtls Weight Loss Wtls ProgramWarm-up Period Heart Rate Control HRC ProgramCustom CST1 or CST2 Programs Using the HRC ProgramClearing the Settings on a Custom Program Advanced Programming Tips Advanced Programming and TroubleshootingSelecting a U.S. Standard or Metric Display RESET, QUICKSTART, ENTER, Select User 2, InclineSelecting Password Protection Viewing the Software Version and Part Numbers Informational DisplaysViewing the Odometer Viewing the Hour MeterER33 AT 12,345,678 Miles 1,714 Hours Viewing the Error LogViewing the Serial Number Troubleshooting Error CodesRcvr Troubleshooting Heart RateInspection Cleaning the EquipmentChecking the Alignment Running Belt Storing the Chest StrapAdjusting the Running Belt Long-Term Storage Servicing the TreadmillLimited Warranty Warranty Periods and CoverageOptions / Accessories This limited warranty shall not apply to Conditions and RestrictionsDisclaimer and Release Exclusion of Consequential and Incidental Damages Exclusive RemediesThank You and Welcome to Precor Tell US about Your NEW Precor Product Page M9.33 Low Impact Treadmill Product SpecificationsQUICKSTARTiTM Choose a Program Assembly Guide Required Tools Hardware Kit Assembly Steps Incline , Speed , Speed M9.3x Low-Impact Treadmills Assembly Guide Checking the Alignment and Adjusting the Running Belt Precor Incorporated 20031 142nd Avenue NE Box