Miele G 7835 operating instructions Installation, Leveling the legs, Removing the lid if necessary

Page 43

Installation

Please refer to the installation diagram supplied with the machine.

,Furniture and fittings installed near the machine must be of a commercial standard, able to withstand the effects of steam.

Installation options

–Free-standing

–Slot-in, next to other machines or

furniture or in a suitable space. The

space must be at least 35 7/16" (90 cm) wide and 29 7/16" (70 cm) deep.

–Undercounter

The machine can be installed under a continuous counter or sink drain.

The niche must be at least: Width 35 7/16" (90 cm) Depth 29 7/16" (75 cm) Height 32 5/16" (82 cm).

The labwasher can be built into a recess of 32 5/16" (82 cm) high by removing the lab washer top.

Leveling the legs

Any unevenness in the floor can be compensated for and the height of the machine raised or lowered by adjusting the four screw feet.

When the feet are screwed in, the machine can be moved back and forth on its rollers.

Removing the lid (if necessary)

^Open the door.

^Remove the fixing screws on both sides using a cross slotted screwdriver.

^Pull the machine lid approx. 5mm forwards, lift upwards and remove.

Protecting the countertop (depending on model)

Important for machines with steam condenser (depending on model):

To prevent steam damage to the

countertop, adhere the protective foil 9 13/16" x 22 13/16" (25 x 58 cm) underneath the countertop near the

steam condenser.

Depending on the requirements for installation, the following kit can be ordered from the Miele Technical Service Department.

Cover plate (protects the countertop)

The underside of the countertop is protected from steam damage by a stainless steel plate.

43

Image 43

Contents Laboratory glassware washer G Contents Contents Use Important Safety InstructionsImportant Safety Instructions Important Safety Instructions Disposal of an old appliance Using accessoriesElectronic controls Guide to the machineCursor right Door switch h Start buttonDisplay On/Off button Cursor leftGuide to the machine To close the door Opening and closing the doorElectric door lock Opening the doorWater softener Softener Capacity Setting the water softenerSelect Unit Enter Water HardnessFilling the salt reservoir Salt indicator Mobile unit coding Automatic mobile unit recognition AWKMobile unit coding strip Setting mobile unit codingSet the program place coding Removing excess soils Preparing the items for cleaningApplications Loading the machineApplications Example upper basket O 190/1 and lower basket U Height adjustable top basketTo adjust the upper basket Spring adapter water connectionInjector unit 1/1 With connection to TA Laboratory glassware LGPreparing the DOS dispensers Adding of liquid detergents and neutralizersAdditional DOS modules optional Filling the containers with liquid cleaning agents Optional Dispensing system maintenancePriming the liquid dispensing systems External Dispensing systemsTo change the operating level Power switchOperation Turning onFixed program Starting a programFree program selection Turning off Program sequenceAutomatic mobile unit recognition AWK Operating levels B or D To change or cancel a programOperating levels a or C Cancelling a program Serial interface Cleaning the filters in the wash cabinet Cleaning and CareCleaning the coarse filter Cleaning the fine, flat and micro-fine filters Tilt the locking clamp to the side Cleaning the drain pump and non-return valveCleaning the filter Cleaning the water inlet filtersCleaning the control panel Cleaning the exteriorChanging the coarse filter Drying unit TA Cleaning and careOpen the door of the storage cabinet Replacing the HEPA-Filter Frequently asked questions After sales service Page Installation Instructions Disposal of the packing materials Caring for the environmentDisposal of an old appliance Protecting the countertop depending on model InstallationLeveling the legs Removing the lid if necessaryWater inlet PlumbingDI-Water connection Drainage This Appliance Must be Grounded Electrical connectionGrounding the machine Re-assembling the service panelEnglish Metric Technical DataPage Page All rights reserved/3404