Miele Programming Special Functions for G 7783 Washer

Page 32

Programming special functions

Press h. "SP" appears in the display.

Press h again. The change has been recorded and the display field clears.

2.Increasing the temperature hold- ing from 10 to 25 minutes in the "Wash" part of the programme, (only in the "B" SPECIAL programme).

Switch off the machine.

Press T1 and c at the same time, hold them in and also switch on the machine with "I-0". The current pro- gramme status "P..." appears in the display.

Press C. "40" or "41" will appear in the display.

"40" = Temp. holding time 10 mins. "41" = Temp. holding time 25 mins.

Press c to change from "40" to "41" or vice versa..

Press h. "SP" appears in the display.

Press h again. The change has been recorded and the display field clears.

Note:

The temperature T1 must not exceed 85 °C, (see "Selecting additional pro- grammes").

3.Adding neutralising agent in the "In- terim rinse 1" part of the programme.

The machine is set at the factory for rinsing agent to be dispensed in the "Final rinse" part of the programme. If neutralising agent is to be dispensed in- stead make the following adjustment:

Switch off the machine.

Press T1 and c at the same time, hold them in and also switch on the machine with "I-0". The current pro- gramme status "P..." appears in the display.

Press B. "50" or "51" will appear in the display.

"50" = Rinsing agent dosage

"51" = Neutralising agent dosage.

Press c to change from "50" to "51" or vice versa..

Press h. "SP" appears in the display.

Press h again. The change has been recorded and the display field clears.

28

Image 32

Contents CD Mielabor Contents Guide to the machine 10 11 12 13 Correct usage Page Page Accessories Disposal of an old machineDescription of the machine Available at extra costSetting the water softener Setting the WaterSoftenerReactivating the water softener, see To close the door Opening and closing the doorTo open the door a Removing excess soils Applications and loadingLoading the machine Loading example 106 Top basket frame can take various inserts109 Adjusting the top basket To adjust the top basketSetting the dosage Rinsing agentAdding Rinsing agent Refilling with rinsing agentAdding detergents Adding neutralising agent and liquid detergentAdding neutralising agent Checking the dispensing system Venting the liquid dispensing system / MaintenanceVenting the liquid dispensing system Adding powder detergent Programme selection Programme B, and when using O-175 or a pipette plateAdding detergent Programme chart = Cold7783 CD Instructions for the operatorPage Page Accessories 93C 70C Switching the machine on and off Selecting a programmeSelecting an additional pro- gramme Programme ChangesSwitching the machine on and off Interrupting a programme Programme sequence indicatorSwitching off 1c. AD water connection 1a. Cold water connection1b. Hot water connection Programming special functions Reactivating the water softener Filling the salt containerSwitch on the machine Position the salt container as followsCleaning and care Cleaning the filters in the water cabinetCleaning the coarse filter Cleaning the fine, flat and micro-fine filtersCleaning the filters in the water inlet Exchanging the S-class particle filter Drying unit TA cleaning and careChanging the Coarse Filter Machine does not start Correcting minor faultsFaults/Possible Causes Position and secure the machine InstallationImportant for machines with DHK steam condensor Cover plate worktop protection To remove service panel and cover plate Electrical connectionElectrical connection Plumbing Connection to the water inletAD connection to purified water, pressurised, 1.5 10 bar Connection to purified water non- pressurised 0 1.5 barDrainage Ventilation of the wash cabinet at rearDisposal of your old machine Caring for the environmentDisposal of the packing material Technical Data Noise emission in dB a