Miele T 7644 C Starting the program, Before the end of a program, End of program Remove laundry

Page 16

Proper drying

Starting the program

The Start/Stop button flashes during program selection. This means that a program can be started.

Press the Start/Stop button. The Start/Stop button lights.

Drying appears in the display and the time remaining is counted down.

Before the end of a program

After the drying phase finished a cooldown phase follows.

The following programs have no cooldown phase: Woolens, Smoothing.

End of program - Remove laundry

0 and End appear in the display to indicate the program end. The buzzer sounds at intervals (when selected).

After the program end the drum rotates reversible in intervals if clothes are not removed (Anti-crease action). This helps to prevent creasing for up to 2 hours.

Press the Door button.

Open the door.

Remove the laundry.

Check that the drum is empty. Laundry left behind may be damaged if dried again.

To save energy, the drum light turns off after a few minutes when the dryer is not operating and the door is open.

To shut it off, press the On/Off button.

Clean the lint filter and lint screens.

Close the door.

Empty the condensed water container (if the condensed water is not drained off externally).

The condenser should be checked at intervals and cleaned as necessary (See the section on "Dryer Care").

16

Image 16

Contents Operating Instructions For condenser tumble dryer T 7644 C Caring for the environment Disposal of packing materialDisposing of your old appliance Saving energyContents Contents Important Safety Instructions This dryer is intended for residential use only Grounding InstructionsAccessories Main Features DescriptionOperating the dryer Dear Customer Function of Miele condenser dryerTo do all this, the dryer is equipped with systems Laundry care anti-crease action and roll-up preventionFault indicator / Optical interface Operating the dryerControl panel DisplayProgram duration/ Estimated time remaining DelayProgrammable functions Care symbols Laundry careDrying tips DryingLaundry care Proper drying Brief instructionsPreparing the laundry Turn on the dryerSelect program Extra options/Select DelayDryness level selection in programs Before the end of a program Starting the programEnd of program Remove laundry Options/Delay DelayGentle BuzzerProgram Overview Normal Extra dry, NormalHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand ironWoolens SmoothingExpress Normal, Hand iron Dress shirts Normal, Hand ironTimed cold Timed warmSwitching over from a running program Changing the program sequenceLoading or removing laundry Time remainingActivating the lock Electronic lockDeactivating the lock Cleaning and care Emptying the condensed water containerCleaning the lint filtration components Cleaning without waterCleaning the dryer Cleaning with waterCleaning the condenser heat exchanger unit Removing the condenser unitChecking the condenser unit Replacing the condenser unit Handle of the unit must be on top, the locking lever downTest and fault messages Trouble shootingWhat to do, if . . . ? Problem Cause Solution Canceling testCanceling the fault Container indicator lightOther problems Problem Cause Solution Water runs from CleanedDryer after Condenser has beenStart and the indicator When switched onCold programs will not Lights for these programsReplacing the light bulb Customer service Program updatesWarranty conditions and warranty period Optional accessoriesInstallation and connection Front viewCarrying the dryer to the installation site Rear view Installation siteWasher-dryer stack Leveling the dryer Ventilating the installation area Before transport at a later dateGeneral Draining condensed water externallyArranging the drain hose Special installation conditions requiring a non-return valve Hooking up the drain hose in sink or floor drainInstallation and connection Electrical connections Technical data Programmable functions for changing Standard values Programmable functions Extending the range of drying levelsBuzzer normal default setting Buzzer loud Adjusting buzzer volumeFor programming and saving in memory, follow steps to Set memory function No Memory default settingMemory Extending cooldown time Default setting Change function of Filter/Vent indicationAdjust keypad tone No Keypad tone default setting Keypad tone onDefault setting Lower conductivity setting Changing water conductivity settingImportant condition Page Page Page Alteration rights reserved Nr 323 260