Miele T 7644 C operating instructions Changing water conductivity setting, Important condition

Page 52

Programmable functions

Changing water conductivity setting

This programmable function should be adjusted only when residual water content is erroneously determined owing to the extreme softness of the water.

Important condition

The water in which fabrics are washed may be extremely soft with a conductivity value less than 150 μS/cm. Drinking water conductivity can be ascertained from your local water supplier.

Activate this programmable function only if the above-mentioned condition applies.

Otherwise the drying result will be unsatisfactory.

For programming and saving in memory, follow steps to .

The function is programmed using the buttons.

Precondition:

–The dryer is switched off.

–The door is closed.

Press Start/Stop and keep it pressed it during steps -.

Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

. . . then release the Start/Stop button.

Press the Gentle button six times.

–The Gentle indicator light flashes once slowly and twice briefly.

–P and 0 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

0Default setting

ILower conductivity setting

(Express indicator light also flashes)

Pressing the Start/Stop button switches from one to the other.

Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

52

Image 52

Contents Operating Instructions For condenser tumble dryer T 7644 C Caring for the environment Disposal of packing materialDisposing of your old appliance Saving energyContents Contents Important Safety Instructions This dryer is intended for residential use only Grounding InstructionsAccessories Main Features DescriptionOperating the dryer Dear Customer Function of Miele condenser dryerTo do all this, the dryer is equipped with systems Laundry care anti-crease action and roll-up preventionFault indicator / Optical interface Operating the dryerControl panel DisplayProgram duration/ Estimated time remaining DelayProgrammable functions Care symbols Laundry careDrying tips DryingLaundry care Proper drying Brief instructionsPreparing the laundry Turn on the dryerSelect program Extra options/Select DelayDryness level selection in programs Before the end of a program Starting the programEnd of program Remove laundry Options/Delay DelayGentle BuzzerProgram Overview Normal Extra dry, NormalHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand ironWoolens SmoothingExpress Normal, Hand iron Dress shirts Normal, Hand ironTimed cold Timed warmSwitching over from a running program Changing the program sequenceLoading or removing laundry Time remainingActivating the lock Electronic lockDeactivating the lock Cleaning and care Emptying the condensed water containerCleaning the lint filtration components Cleaning without waterCleaning the dryer Cleaning with waterCleaning the condenser heat exchanger unit Removing the condenser unitChecking the condenser unit Replacing the condenser unit Handle of the unit must be on top, the locking lever downTest and fault messages Trouble shootingWhat to do, if . . . ? Problem Cause Solution Canceling testCanceling the fault Container indicator lightOther problems Problem Cause Solution Water runs from CleanedDryer after Condenser has beenStart and the indicator When switched onCold programs will not Lights for these programsReplacing the light bulb Customer service Program updatesWarranty conditions and warranty period Optional accessoriesInstallation and connection Front viewCarrying the dryer to the installation site Rear view Installation siteWasher-dryer stack Leveling the dryer Ventilating the installation area Before transport at a later dateGeneral Draining condensed water externallyArranging the drain hose Special installation conditions requiring a non-return valve Hooking up the drain hose in sink or floor drainInstallation and connection Electrical connections Technical data Programmable functions for changing Standard values Programmable functions Extending the range of drying levelsBuzzer normal default setting Buzzer loud Adjusting buzzer volumeFor programming and saving in memory, follow steps to Set memory function No Memory default settingMemory Extending cooldown time Default setting Change function of Filter/Vent indicationAdjust keypad tone No Keypad tone default setting Keypad tone onDefault setting Lower conductivity setting Changing water conductivity settingImportant condition Page Page Page Alteration rights reserved Nr 323 260