Miele T 7644 C Adjust keypad tone, No Keypad tone default setting Keypad tone on

Page 51

Programmable functions

Adjust keypad tone

An audible tone sounds every time a button is pressed.

For programming and saving in memory, follow steps to .

The programmable function is programmed using the buttons.

Precondition:

–The dryer is switched off.

–The door is closed.

Press Start/Stop and keep it pressed it during steps -.

Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

. . . then release the Start/Stop button.

Press the Gentle button five times.

–The Gentle indicator light flashes once slowly and once briefly.

–P and 0 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

0no Keypad tone (default setting)

IKeypad tone on

(Express indicator light also flashes)

Pressing the Start/Stop button switches from one to the other.

Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

51

Image 51

Contents Operating Instructions For condenser tumble dryer T 7644 C Saving energy Caring for the environmentDisposal of packing material Disposing of your old applianceContents Contents Important Safety Instructions Grounding Instructions This dryer is intended for residential use onlyAccessories Function of Miele condenser dryer Main FeaturesDescription Operating the dryer Dear CustomerLaundry care anti-crease action and roll-up prevention To do all this, the dryer is equipped with systemsDisplay Fault indicator / Optical interfaceOperating the dryer Control panelDelay Program duration/ Estimated time remainingProgrammable functions Drying Care symbolsLaundry care Drying tipsLaundry care Turn on the dryer Proper dryingBrief instructions Preparing the laundryExtra options/Select Delay Select programDryness level selection in programs Starting the program Before the end of a programEnd of program Remove laundry Buzzer Options/DelayDelay GentleWrinkle-free Extra dry, Normal, Hand iron Program OverviewNormal Extra dry, Normal Hand iron, Rotary ironDress shirts Normal, Hand iron WoolensSmoothing Express Normal, Hand ironTimed warm Timed coldTime remaining Switching over from a running programChanging the program sequence Loading or removing laundryElectronic lock Activating the lockDeactivating the lock Emptying the condensed water container Cleaning and careCleaning without water Cleaning the lint filtration componentsCleaning with water Cleaning the dryerRemoving the condenser unit Cleaning the condenser heat exchanger unitChecking the condenser unit Handle of the unit must be on top, the locking lever down Replacing the condenser unitTrouble shooting Test and fault messagesWhat to do, if . . . ? Container indicator light Problem Cause SolutionCanceling test Canceling the faultOther problems Condenser has been Problem Cause Solution Water runs fromCleaned Dryer afterLights for these programs Start and the indicatorWhen switched on Cold programs will notReplacing the light bulb Optional accessories Customer serviceProgram updates Warranty conditions and warranty periodFront view Installation and connectionRear view Installation site Carrying the dryer to the installation siteWasher-dryer stack Leveling the dryer Before transport at a later date Ventilating the installation areaDraining condensed water externally GeneralArranging the drain hose Hooking up the drain hose in sink or floor drain Special installation conditions requiring a non-return valveInstallation and connection Electrical connections Technical data Programmable functions for changing Standard values Extending the range of drying levels Programmable functionsAdjusting buzzer volume Buzzer normal default setting Buzzer loudFor programming and saving in memory, follow steps to No Memory default setting Set memory functionMemory Extending cooldown time Change function of Filter/Vent indication Default settingNo Keypad tone default setting Keypad tone on Adjust keypad toneChanging water conductivity setting Default setting Lower conductivity settingImportant condition Page Page Page Alteration rights reserved Nr 323 260