Miele T 7644 C operating instructions Accessories

Page 7

IMPORTANT SAFETY INSTRUCTIONS

￿The dryer should not be operated without its condenser unit.

￿Lint screens and door lint filter must be dried after wet cleaning. Wet screens may cause faulty dryer operation!

￿Do not place the dryer in a room where there is a risk of frost occurring. Temperatures around the freezing point affect dryer performance.

Condensed water freezing in the pump and the drain hose can lead to damage.

Permissible room temperature musts be between +2°C and +35°C.

￿If the condensed water is drained externally, you must secure the drain hose against slipping off, if for example it is hanging from a sink.

If the hose slips off, the condensed water released can cause damage.

￿Condensed water is not potable.

It can endanger the health of people and pets.

￿Keep the room in which the dryer is installed free of dust and fluff.

Dirt particles in the incoming cooling air impair performance.

￿Do not sit or lean on the door. The dryer might tip over.

￿Close the door after every drying cycle. In this way you can prevent

children from trying to climb into the dryer or leaving objects inside it.

Pets or small animals from getting into the dryer.

￿Do not hose down the dryer.

Accessories

￿Accessory parts may only be attached or installed when they have been expressly approved by Miele. If other parts are added or installed, guarantee, performance and/or product liability claims are invalidated.

The manufacturer will not be held liable for damage caused by failure to comply with the safety instructions and warnings.

SAVE THESE INSTRUCTIONS

7

Image 7
Contents Operating Instructions For condenser tumble dryer T 7644 C Saving energy Caring for the environmentDisposal of packing material Disposing of your old applianceContents Contents Important Safety Instructions Grounding Instructions This dryer is intended for residential use onlyAccessories Function of Miele condenser dryer Main FeaturesDescription Operating the dryer Dear CustomerLaundry care anti-crease action and roll-up prevention To do all this, the dryer is equipped with systemsDisplay Fault indicator / Optical interfaceOperating the dryer Control panelProgram duration/ Estimated time remaining DelayProgrammable functions Drying Care symbolsLaundry care Drying tipsLaundry care Turn on the dryer Proper dryingBrief instructions Preparing the laundrySelect program Extra options/Select DelayDryness level selection in programs Before the end of a program Starting the programEnd of program Remove laundry Buzzer Options/DelayDelay GentleWrinkle-free Extra dry, Normal, Hand iron Program OverviewNormal Extra dry, Normal Hand iron, Rotary ironDress shirts Normal, Hand iron WoolensSmoothing Express Normal, Hand ironTimed warm Timed coldTime remaining Switching over from a running programChanging the program sequence Loading or removing laundryActivating the lock Electronic lockDeactivating the lock Emptying the condensed water container Cleaning and careCleaning without water Cleaning the lint filtration componentsCleaning with water Cleaning the dryerRemoving the condenser unit Cleaning the condenser heat exchanger unitChecking the condenser unit Handle of the unit must be on top, the locking lever down Replacing the condenser unitTest and fault messages Trouble shootingWhat to do, if . . . ? Container indicator light Problem Cause SolutionCanceling test Canceling the faultOther problems Condenser has been Problem Cause Solution Water runs fromCleaned Dryer afterLights for these programs Start and the indicatorWhen switched on Cold programs will notReplacing the light bulb Optional accessories Customer serviceProgram updates Warranty conditions and warranty periodFront view Installation and connectionCarrying the dryer to the installation site Rear view Installation siteWasher-dryer stack Leveling the dryer Before transport at a later date Ventilating the installation areaGeneral Draining condensed water externallyArranging the drain hose Hooking up the drain hose in sink or floor drain Special installation conditions requiring a non-return valveInstallation and connection Electrical connections Technical data Programmable functions for changing Standard values Extending the range of drying levels Programmable functionsBuzzer normal default setting Buzzer loud Adjusting buzzer volumeFor programming and saving in memory, follow steps to Set memory function No Memory default settingMemory Extending cooldown time Change function of Filter/Vent indication Default settingNo Keypad tone default setting Keypad tone on Adjust keypad toneDefault setting Lower conductivity setting Changing water conductivity settingImportant condition Page Page Page Alteration rights reserved Nr 323 260