Miele T 7644 C operating instructions Extending cooldown time

Page 49

Programmable functions

Extending cooldown time

You can individually lengthen the cooldown phase the occurs before the end of a program. Fabrics will be more completely cooled down.

Cooldown time

–can be extended by two stages.

–it does not function for Smoothing programme.

For programming and saving in memory, follow steps to .

The programmable function is programmed using the buttons.

Precondition:

–The dryer is switched off.

–The door is closed.

Press Start/Stop and keep it pressed it during steps -.

Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

. . . then release the Start/Stop button.

Press the Gentle button three times.

–The Gentle indicator light flashes briefly seven times.

–P and 0 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

0Default setting

IFive minutes longer cooldown time (Express indicator light will flash once)

2Ten minutes longer cooldown time (Express indicator light will also flash twice)

Pressing the Start/Stop button switches from one to the other.

Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

49

Image 49

Contents Operating Instructions For condenser tumble dryer T 7644 C Disposal of packing material Caring for the environmentDisposing of your old appliance Saving energyContents Contents Important Safety Instructions Grounding Instructions This dryer is intended for residential use onlyAccessories Description Main FeaturesOperating the dryer Dear Customer Function of Miele condenser dryerLaundry care anti-crease action and roll-up prevention To do all this, the dryer is equipped with systemsOperating the dryer Fault indicator / Optical interfaceControl panel DisplayProgram duration/ Estimated time remaining DelayProgrammable functions Laundry care Care symbolsDrying tips DryingLaundry care Brief instructions Proper dryingPreparing the laundry Turn on the dryerSelect program Extra options/Select DelayDryness level selection in programs Before the end of a program Starting the programEnd of program Remove laundry Delay Options/DelayGentle BuzzerNormal Extra dry, Normal Program OverviewHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand ironSmoothing WoolensExpress Normal, Hand iron Dress shirts Normal, Hand ironTimed warm Timed coldChanging the program sequence Switching over from a running programLoading or removing laundry Time remainingActivating the lock Electronic lockDeactivating the lock Emptying the condensed water container Cleaning and careCleaning without water Cleaning the lint filtration componentsCleaning with water Cleaning the dryerRemoving the condenser unit Cleaning the condenser heat exchanger unitChecking the condenser unit Handle of the unit must be on top, the locking lever down Replacing the condenser unitTest and fault messages Trouble shootingWhat to do, if . . . ? Canceling test Problem Cause SolutionCanceling the fault Container indicator lightOther problems Cleaned Problem Cause Solution Water runs fromDryer after Condenser has beenWhen switched on Start and the indicatorCold programs will not Lights for these programsReplacing the light bulb Program updates Customer serviceWarranty conditions and warranty period Optional accessoriesFront view Installation and connectionCarrying the dryer to the installation site Rear view Installation siteWasher-dryer stack Leveling the dryer Before transport at a later date Ventilating the installation areaGeneral Draining condensed water externallyArranging the drain hose Hooking up the drain hose in sink or floor drain Special installation conditions requiring a non-return valveInstallation and connection Electrical connections Technical data Programmable functions for changing Standard values Extending the range of drying levels Programmable functionsBuzzer normal default setting Buzzer loud Adjusting buzzer volumeFor programming and saving in memory, follow steps to Set memory function No Memory default settingMemory Extending cooldown time Change function of Filter/Vent indication Default settingNo Keypad tone default setting Keypad tone on Adjust keypad toneDefault setting Lower conductivity setting Changing water conductivity settingImportant condition Page Page Page Alteration rights reserved Nr 323 260