Miele T 7644 C operating instructions Change function of Filter/Vent indication, Default setting

Page 50

Programmable functions

Change function of Filter/Vent indication

Lint should be removed after drying. At the same time, the Filter/Vent indicator light reminds you to do so as soon as a certain degree of lint has accumulated. You can yourself decide which degree of lint accumulation will trigger that reminder.

Determine by trial and error which of the four options responds to your drying practices.

For programming and saving in memory, follow steps to .

The programmable function is programmed using the buttons.

Precondition:

–The dryer is switched off.

–The door is closed.

Press Start/Stop and keep it pressed it during steps -.

Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

. . . then release the Start/Stop button.

Press the Gentle button four times.

–The Gentle indicator light flashes once slowly.

–P and 2 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

0The Filter/Vent indicator is deactivated

IThe Filter/Vent indicator comes on only when there is a heavy lint buildup

(Express control light additionally flashes once)

2default setting

(the Express indicator light also flashes twice)

3The Filter/Vent indicator will come on when there is only a light lint buildup

(The Express indicator light also flashes three times)

Pressing the Start/Stop button switches from one to the other.

Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

50

Image 50

Contents Operating Instructions For condenser tumble dryer T 7644 C Disposing of your old appliance Caring for the environmentDisposal of packing material Saving energyContents Contents Important Safety Instructions This dryer is intended for residential use only Grounding InstructionsAccessories Operating the dryer Dear Customer Main FeaturesDescription Function of Miele condenser dryerTo do all this, the dryer is equipped with systems Laundry care anti-crease action and roll-up preventionControl panel Fault indicator / Optical interfaceOperating the dryer DisplayProgrammable functions DelayProgram duration/ Estimated time remaining Drying tips Care symbolsLaundry care DryingLaundry care Preparing the laundry Proper dryingBrief instructions Turn on the dryerDryness level selection in programs Extra options/Select DelaySelect program End of program Remove laundry Starting the programBefore the end of a program Gentle Options/DelayDelay BuzzerHand iron, Rotary iron Program OverviewNormal Extra dry, Normal Wrinkle-free Extra dry, Normal, Hand ironExpress Normal, Hand iron WoolensSmoothing Dress shirts Normal, Hand ironTimed cold Timed warmLoading or removing laundry Switching over from a running programChanging the program sequence Time remainingDeactivating the lock Electronic lockActivating the lock Cleaning and care Emptying the condensed water containerCleaning the lint filtration components Cleaning without waterCleaning the dryer Cleaning with waterCleaning the condenser heat exchanger unit Removing the condenser unitChecking the condenser unit Replacing the condenser unit Handle of the unit must be on top, the locking lever downWhat to do, if . . . ? Trouble shootingTest and fault messages Canceling the fault Problem Cause SolutionCanceling test Container indicator lightOther problems Dryer after Problem Cause Solution Water runs fromCleaned Condenser has beenCold programs will not Start and the indicatorWhen switched on Lights for these programsReplacing the light bulb Warranty conditions and warranty period Customer serviceProgram updates Optional accessoriesInstallation and connection Front viewWasher-dryer stack Rear view Installation siteCarrying the dryer to the installation site Leveling the dryer Ventilating the installation area Before transport at a later dateArranging the drain hose Draining condensed water externallyGeneral Special installation conditions requiring a non-return valve Hooking up the drain hose in sink or floor drainInstallation and connection Electrical connections Technical data Programmable functions for changing Standard values Programmable functions Extending the range of drying levelsFor programming and saving in memory, follow steps to Adjusting buzzer volumeBuzzer normal default setting Buzzer loud Memory No Memory default settingSet memory function Extending cooldown time Default setting Change function of Filter/Vent indicationAdjust keypad tone No Keypad tone default setting Keypad tone onImportant condition Changing water conductivity settingDefault setting Lower conductivity setting Page Page Page Alteration rights reserved Nr 323 260