NEC MD-15 warranty Controls at a glance, Select cycle

Page 6

Controls at a glance

Control features and styling vary by model.

Step 1 Select cycle

INTELLIDRY WRINKLE FREE FABRICS WITH PRESS CARE automatically senses the moisture in the load and shuts off when the selected dryness level is reached. It minimizes wrin- kles in synthetic fabrics such as acrylic, nylon, polyester or blends by providing an unheated cool-down period at the end of the cycle. Simply set the control to the desired dryness level (MORE DRY – LESS DRY). The line between MORE DRY and LESS DRY is the initial preferred setting for the majority of loads.

INTELLIDRY REGULAR automatically senses the moisture in the load and shuts off when the selected dryness level is reached. This cycle is designed for loads such as towels, under- wear, t-shirts, jeans, etc. Set the control to the desired dryness level (MORE DRY – LESS DRY). The line between MORE DRY and LESS DRY is the initial preferred setting for the majority of loads.

WRINKLE RELEASE will release wrin- kles from items that are clean and dry but slightly wrinkled, such as from a crowded closet, packed suitcase or from sitting in the dryer too long after the end of the cycle. It provides 10 minutes of heated tumbling and 5 minutes of cool down tumbling without heat.

DAMP DRY is designed to “partially” dry items. It provides approximately 20 minutes of heated tumbling and 5 minutes of cool down tumbling without heat.

DRYEL FABRIC CARE (select models)

is designed for use on dry clean only fabrics in combination with Dryel Dry Clean Only Fabric Care product. Placing the control dial arrow at the DRYEL line will provide the optimal amount of time needed to properly use Dryel. (For more information on using the Dryel cycle, see page 7.)

TIME DRY/AIR FLUFF may be select- ed for any load if the IntelliDry sensor sys- tem is not used. Set the control to the desired number of minutes and choose the appropriate drying temperature for the load.

NOTE

The dial can be turned in either direction to select a cycle. Once started, the dial will not advance at a specific rate during the IntelliDry cycles. At first the dial may not advance at all. Toward the end of the cycle (when the load begins to dry) the dial will advance at a more regular rate and much more quickly. This is normal operation.

5

Image 6
Contents Intellidry Dryer MD-15 CanadaImportant Safety Instructions Al injury or deathRecognize safety symbols, words, labels Safety notice & warningDryer Exhaust Tips Don’tClean the lint filter Load the dryer properlyControls at a glance Select cycleTo Use Rack Select temperaturePress start Part No. MAL1000AXX To order callUsing the Dryel Setting select models Refer to the Dryel instructions for proper useRemove the hinge hole covers and screws Replacing the Drum LightCabinet wipe off any marks with soap and water Replace the hinge hole covers to the opposite sideSpecial Laundry Tips Be sure the door is latched shut Select the More DRY setting if desiredBefore YOU Call Check the home’s circuit breaker and fusesLimited Warranty To receive warranty serviceFull One Year Warranty Canadian ResidentsLa date dorigine Du lundi au vendredi, 8 h à 8 h, heure de l’estOu la compagnie de gaz Mesures DE Sécurité ImportantesBlessures et décès Ne pas modifier les mécanismes de com- mandeMesures de sécurité importantes Ne pas faire Conseils Pour L’ÉVACUATION DE L’AIRFaire Ne pasConseils DE Fonctionnement En mettant une seule charge de machine à laver à la foisCommandes en bref Étape 1 Sélectionner le cycleOuvrir la porte de la sécheuse Utilisation de la grilleEnlèvement de la grille Part No. MAL1000AXXÉtape 2 Mettre la commande sur Dryel Étape 3 Appuyer sur le bouton «start» mise en marcheDuvetage Remplacement de lampoule EntretienConseils DE Blanchissage Avant D’APPELER LE Service DE Dépannage Vérifier les points ci-dessus. De plusDeuxième année Toutes les pièces Garantie totale d’un anGarantie limitée des pièces Résidents canadiensSecado Inteligente MD-15 Número de Modelo Número de Serie Date d’achatNo altere los controles Personales o la muerteCados o por la compañía de gas Limpie el filtro de pelusa antes o después de cada cargaAviso y advertencia de seguridad importantes Qué hacer Qué no hacerSu secadora nueva. Asegúrese Sugerencias Para LA Operación Después de cada carga Para reducir el tiempo de secadoNo opere la secadora sin el filtro para pelusa Los controles a simple vista Paso 1 Seleccione el CicloUso de la Rejilla Paso 2 Seleccione la temperaturaPaso 3 Oprima start arranque Abra la puerta de la secadoraUsando EL Función DEL Dryel algunos modelos Reemplazo SE LA LUZ Tambor Inversión DE LA PuertaInstrucciones para reemplazar el foco Cobertores Evite secar dandos vueltasSobrecamas ColchasAntes DE Llamar Revise todo lo anterior, y ademásSegundo Año Todas las piezas Un año de garantía en partes y mano de obraGarantía Limitada Residentes de Canadá