Cisco Systems Cisco Unity 3.1 manual To specify switch settings for Cisco CallManager

Page 28

Dual Phone System Integration

Changing Cisco Unity Administrator Settings

The access code is the same number that subscribers on the circuit-switched phone system dial to reach someone on the Cisco CallManager system.

Step 3 Adjust other settings as applicable. For more information about the other settings on the Switch page, refer to the Cisco Unity Administrator Help.

Step 4 Click the Save icon, then click OK in the Warning dialog box.

To specify switch settings for Cisco CallManager

Step 1

Go to System > Switch > IP Switch.

Step 2

In the Set Active Switch Type section, enter values as shown in the following table:

 

Table 23

Switch Settings

 

 

 

 

 

Switch Parameter

Required Setting

 

 

 

 

 

Manufacturer

 

Cisco

 

 

 

 

 

Model

 

CallManager

 

 

 

 

Switch PBX software version

3.01 or later

 

 

 

 

 

Integration

 

TAPI

 

 

 

Step 3

Click Set As Active, then click OK in the Warning dialog box.

Step 4

In the Access Code field, enter the trunk access code that Cisco Unity must dial to transfer calls to the

 

circuit-switched phone system from Cisco CallManager.

The access code is the same number that subscribers on Cisco CallManager dial to reach someone on the circuit-switched phone system.

Step 5 Click the Save icon, then click OK in the Warning dialog box.

To Modify Voice Port Settings

Step 1 In the Cisco Unity Administrator, go to the System > Ports page.

Step 2 In the Port Assignments section, indicate the range of ports to be assigned to the circuit-switched phone system. The port range for the circuit-switched phone system begins with 1 and extends to no more than the number of ports that are on the installed voice cards. Do not assign more ports to the circuit-switched phone system than the number of ports on the voice cards.

Caution If you assign fewer voice ports to the circuit-switched phone system than are available on the installed voice cards, you must edit the registry for this port range to take effect. Otherwise, all available voice ports on the voice cards are used in the integration regardless of the Port Assignments settings. For information on editing the registry for the port range, see the appendix “Assigning Dialogic Ports for a Dual Phone System Integration.”

Step 3 In the Port Assignments section, indicate the range of ports to be assigned to Cisco CallManager. The port range must begin with the next port after the last port for the circuit-switched phone system. The range for Cisco CallManager must end with the port number of the last port displayed on the Ports page,

Avaya Definity Gx/PBXLink Integration Guide for Cisco Unity 3.1

28

OL-1846-06

 

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Integration Tasks Integration StepsPhone System RequirementsCisco Unity Server Configuration for 24 or Fewer Ports Configuration for 25 to 48 PortsConfiguration for 49 to 72 Ports Integration DescriptionPBXLink Box Connections Integration Features Number of Voice Messaging Ports to InstallProgramming the Avaya Definity/PBXLink Phone System Number of Voice Messaging Ports That Will Answer CallsTo program the Avaya Definity/PBXLink phone system Option SettingOption Button Assignment Setting Call-apprNormal Inspect Call-apprFeature Button Number Setting Abrdg-appr Extn 1st voice mail extensionAbrdg-appr Extn 2nd voice mail extension Abrdg-appr Extn 3rd voice mail extensionAbrdg-appr Extn 4th voice mail extension Abrdg-appr Extn 7th voice mail extensionEvery third remaining voice mail extension Abrdg-appr Extn 5th voice mail extensionCOR EnterVector Definition Options for Call Vector Avaya Definity Gx/PBXLink Integration Guide for Cisco Unity To set up user phones To Update the PBXLink Box Firmware Setting up the PBXLink BoxClick PBXLinkFirmwareUpdate To set up the PBXLink box Select Configuration and press EnterTo set up the port LTNs for three PBXLink digital ports To set up the port LTNs for two PBXLink digital portsLTN Number Voice Messaging Port Value 0007 Configuring Cisco Unity for the Integration To confirm that the integration is enabledGo to System Licensing Licensed Features Switch Parameter Required SettingTesting the Integration To Set Up the Test ConfigurationTo Test an External Call with Release Transfer To Test an Internal Call with Release TransferTo Return Example Subscriber to the Default Settings To Set Up Supervised Transfer on Cisco UnityTo Test Supervised Transfer Integrating a Secondary Server for Cisco Unity Failover RequirementsTo Set Up the Secondary Server for Failover Setting Up the Secondary Server for FailoverIntegration Description Integration Steps When No Phone Systems Are Installed Dual Phone System Integration OverviewReinstall the TSP. See the To Reinstall the TSP procedure on Changing Cisco Unity Administrator Settings Go to System Switch IP Switch To specify switch settings for Cisco CallManagerTo Modify Voice Port Settings Page Changing the Number of Installed Ports To Remove the Existing TSPSetting Up Cisco Unity to Remap Extension Numbers About the Remapping FeatureTo Reinstall the TSP To Remap Extension Numbers Wildcard Syntax and ExamplesRule Original Number New Number To Set the Port Assignments in the Registry System Configuration Settings ConventionsConvention Description Ctrl-Alt-DeleteCisco.com Obtaining DocumentationDocumentation DVD Cisco Product Security Overview Documentation FeedbackOrdering Documentation Obtaining Technical Assistance Reporting Security Problems in Cisco ProductsCisco Technical Support Website Submitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information
Top Page Image Contents