Kenmore 796.8051 manual KEY Dimensions Specifications, Manufactured Homes on

Page 8

II

	KEY DIMENSIONS		AND SPECIFICATIONS
Description			Dryer (Gas and Electric)
Electrical Requirements			Please refer to the rating label.
Gas	Requirements*	NG:	6-8 in. WC
Gas	Requirements*	LP:	10-13 in. WC
Dimensions			27" (W) X 28 11/16" (D) X 38" (H), 52 1/4" (D With door open)
			68.60m (W) X 76.7cm (D) X 96.50m (H), 132.7cm (D With door open)
Net Weight			Electric: 139 lb. (63.1kg) Gas: 142.4 lb. (64.6kg)
Drying Capacity			IEC 7.4 cu. ft.
*Gas	Models only.

LOCATION REQUIREMENTS

IMPORTANT:

Read all installation instructions completely before installing and operating your dryer!

It is important that you review this entire manual before installing and using your dryer. It contains detailed instructions concerning electrical connections, gas con- nections and exhaust requirements.

I

203/20"

(56.2 cm)

CHOOSE THE PROPER	LOCATION
• Store and install the dryer	where it will not be exposed	(1
to temperatures below freezing or exposed to outdoor

weather conditions.

•Choose a location with a solid, level floor.

•If the dryer is being installed in a garage, place the dryer at least 18 in. (45.7cm) above the floor.

•Properly ground the dryer to conform with all governing codes and ordinances.

•To reduce the risk of electric shock, do not install the dryer in damp or wet locations.

	IMPORTANT:	If you are	installing your		dryer in a
	manufactured	or mobile	home,	please	refer to the	3"
	section Special Electrical Requirements for Mobile or					3"
	section Special Electrical Requirements for Mobile or
	Manufactured	Homes on page		12,		(7.6 cm)

oL

/' /

,, t<

CLEARANCES

•Most installations require a minimum 5-1/2 in.

(14 cm) clearance behind the dryer for the exhaust ducting.

•Allow minimum clearances of at least 1 in.

(2.5 cm) on the sides and back to minimize vibration and noise.

•Allowing additional clearance for installation and servicing is recommended.

•Be sure to allow for wall, door, or floor moldings that may increase the required clearances.

•Allow at least 21 in. (53.3 cm) in front of the dryer to open the door.

48 sq in. /

(310 cm)

io

34 sq in.

(155cm)"

i I

(7.6 cm)

(2.5 cm)

27"

(2.5 cm)

(68.6 cm)

1

Additional Instructions for

closet installations:

•The closet door must allow for sufficient airflow. Refer to the diagram to the left for minimum vent opening requirements. A Iouvered door is also acceptable.

Closet Door Vent

Requirements

8

II

Image 8

Contents Secadora Maintenance InstallationMaster Protection Agreements CongratUlations on making a smart purchase, Your newRead ALL Instructions Before USE Basic Safety Precautions Follow basic precautions, including the followingGas dryers Must be exhausted to the outside Place dryer at least 18 in. above the floor for aDo not place candle and cigarettes on top Safety Instructions for Connecting Electricity For personal safety, this dryer must be properlyKEY Parts and Components EASY-TO-USE Control PanelKEY Dimensions Specifications Additional Instructions for Closet installationsSection Special Electrical Requirements for Mobile or Manufactured Homes onRequired Dimensions for Installation With Stacking Kit Required Dimensions for Installation With PedestalInstallation with Optional Pedestal Base or Stacking KIT GAS Requirements GAS Models Connecting GAS Dryers Electrical Requirements for Gas Models OnlyConnecting GAS Dryers Connecting the Gas SupplyHigh-Altitude Installations Proceed to Venting the Dryer onElectrical Requirements Connecting Electric Dryers WAR Ning ToreducetheriskoffireThree-Wire Power Cord Connecting Electric DryersFour-Wire Power Cord Selecting and Verifying Duct Length Chart Venting the Dryer Check Your Exhaust System for ProblemsUsing the Duct Requirements Chart below Venting the Dryer Routing and Connecting DuctworkConnecting the Dryer Vent Leveling the Dryer Reversing the Door SwingFinal Installation Check Testing Dryer HeatingChecking Venting Checking LevelnessControl Panel Features Cycle Selector KnobClean the Lint Filter Operating the DryerCycle Guide Rack DryModifiersOptions Sensor Dry Cycles Manual Dry CyclesSorting Loads Loading the DryerCheck the Lint Filter Before Every Load Fabric Care LabelsEstimated Time Remaining Check Vent Indicator Lint Filter IndicatorControl Lock Indicator Cycle Status IndicatorCycle Modifier Buttons Dry LevelCycle Options and Special Features Wrinkle Guard Rack DRY CycleRegular Cleaning Cleaning the ExteriorCleaning the Lint Filter Cleaning Around and Under the DryerBefore Calling for Service Check Vent Indicator is Blinking Greasy or dirty spots on clothesDryer will not turn on Dryer does not heatBefore Calling for SERVICEcont Drying time is not consistentClothes take too long to dry Check ThenClothes are shrinking Before Calling for ServiceClothes are wrinkled Optional Accessories Stacking KIT InstallationTools Needed for Installation This stacking kit includesTools Needed Pedestal InstallationList of Parts Side Venting KIT Installation Option 2 Bottom ventingOne-Year Limited Warranty Disclaimer of implied warranties limitation of remediesPage Garantja LEA Todas LA Instrucciones Antes DE Usar Precauciones Basicas DE Seguridad Instrucciones Importante Para LA Instalacion Guarde Estas Instrucciones Piezas Y Componentes Significativos Panel DE Control F,,CIL DE UsarEn armario Dimensiones Y Especificaciones SignificativasInstrucciones Adicionales Dimensiones precisas para la instalacion con pedestal Instalacion CON Base DE Pedestal O KIT DE Apilado OpcionalRequerimientos electricos solo para modelos de gas Conexion DE LAS Secadoras DE GAS Conexidn del suministro de gasRequerimientos DE Elictricos CONEXlON DE LAS Secadoras DE ElictricasCable de alimentacion trifilar CONEXlON DE LAS Secadoras DE ElictricasCable De alimentacion Tetrafilar 77!i!!ili!777777777777777777777777 Ventilacion DE LA SecadoraCuadro de seleccion y comprobacion de Iongitud del conducto Conexion del conducto de ventilacion de la secadora Ventilacion DE LA SecadoraTrayectoria y conexion de los conductos Nivelacion DE LA Secadora Cambio DE Sentido DEL Giro DE Apertura DE LA PuertaComprobacion Final DE LA Instalacion Prueba de calentamiento de la secadoraComprobacion de la ventilacion Comprobacion de la nivelacionBoton Power enc./apag Funciones DEL Panel DE ControlFuncionamiento DE LA Secadora Cargar LA SecadoraSecado DesinDeja Clasificacion DE Cargas Carga DE LA SecadoraComprobar EL Filtro DE Pelusas Antes DE Cada Carga Etiquetas de prendas delicadasSistema DE DETECClON DE Bloqueo DEL La temperatura entre Botones Modificadores DE CicloTimed Opciones DEL Ciclo Y Funciones Especiales Wrinkle Guard anti-arrugasControl Lock bloqueo de controles MY Cycle mi cicloLimpieza del exterior Limpieza del filtro de pelusasLimpieza del interior Limpieza alrededor y bajo la secadoraLa secadora no se enciende La secadora no calientaManchas de grasa o suciedad en las prendas Antes DE Solicitar Asistencia TicnicaAntes DE Solicitar Asistencia TleCNICA El tiempo de secado no es consistenteLas prendas tardan mucho en secarse La pantalla Muestra el codigo de error TEl 6 TE2 Las prendas estan arrugadasLas prendas han encogido Pelusa sobre las prendasAccesorios Opcionales Instalacion DEL KIT DE ApiladoEste kit de apilado incluye Herramientas necesarias para la instalacionListado de piezas Herramientas necesariasInstalacion DEL Pedestal Una instalacion incorrectapuedeprovocaraccidentesgravesInstalacion DEL KIT DE Ventilacion Lateral Opci6n 2 ventilaci6n por la baseGarantia limitada de un aho Page Page