Bosch Appliances WTXD5321CN, WTXD5321US installation instructions Exhaust Air Connection

7. Attach the 2 power cord outer conductors (red and black) to the terminals labeled L and the remaining power cord conductor (white) to the terminal labeled N.

8.

Attach

the

2 power cord

outer

Exhaust

air

connection

conductors (red and black) to the 2

terminals labeled L and the

d WARNING

d

remaining

power

cord

conductor

(white)

to

the

terminal

labeled

N.

9.

Tighten

all

3 screws

(3 Nm) so that

1.

To

reduce

the

risk

of

fire,

this

drye

the

power

conductors

are

held

MUST

BE

EXHAUSTED

securely

in

place .

OUTDOORS.

2.

To

reduce

the

risk

of

fire,

do

not

use

the

ductwork

longer

than

recommended.

3.

DO NOT use a plastic or

9. Check

the

U.L.

strain

relief clamp

nonometal

duct

with

this

dryer.

4.

DO NOT use a duct smaller than

to make sure that it is tight and

inches

in

diameter.

cannot

be turned.

5.

DO

NOT

use

exhaust

hoods with

10. Replace

the

cover

on

the terminal

magnetic

latches.

block and

fasten

in

place.

6.

DO

NOT

exhaust the dryer into a

i

10.

Check

the

U.L.

strain

relief clamp

Make

sure

that

the

U.L. strain relief

chimney,

furnace cold

air

duct,

clamp

is

outside

the

cover!

attic, crawl space, or any other

to

make

sure

that

it

is tight

and

Additional

grounding

procedure

ductwork

used

for

venting.

cannot

be

turned.

7.

DO

NOT

install

a

flexible

duct

in a

11.

Replace

the cover

on

the

terminal

-

Some

local

regulations

may

enclosed

wall,

ceiling

or

floor.

block

and

fasten

in place.

8.

DO

NOT

crush or kink the duct.

require

a

separate

ground. In such

i

Make

sure

that the U.L. strain relief

cases,

the

required

accessory

9.

Do

clean

and

inspect

the

exhaust

clamp is outside the cover!

ground

wire, clamp

and screw

system on a regular basis; at least

The appliance is now ready to be

must be

purchased

separately.

once

a

year.

plugged into the 4owire receptacle

of

-

Never

ground the

dryer to plastic

10.

The

exhaust

duct

must terminate

the

power

rating.

plumbing lines, gas lines or water

in a

manner

to

prevent

back drafts

Connecting

3Wwire

power

supply

pipes.

or

entry

of

birds

or

other

wildlife.

cord

Grounding

instruction

The

Siemens

dryers

are

intended to

be

1.

Remove

the screws

from

the

coverThis

appliance

must

be

grounded.

In

vented outdoors.

To

prevent

buildoup

of

the

terminal

block

located

at

the

event

of

a

malfunction or

top

rear

of

the

appliance.

the

of moisture and accumulation of lint

2.

breakdown,

grounding

will

reduce

the

indoors, as well as to maintain

Make

sure

that

there

is

risk

of

electric shock

by

providing

a

maximum

drying

efficiency,

it

is

a grounding

strap.

path

of

least

resistance

for the electricrecommended

that

the

dryer

is

vented

3.

Fix

the

strain

relief

clamp

to

the

current.

outdoors.

angle

bracket.

Tighten

the

nut.

For

Canada

the

dryer

comes with

a

Exhaust

air

outlet

on

the

dryer

4.

Loosen

the

2

screws

labeledL and

cord

which

has

an

equipment

The

dryer

is

delivered

with an

exhaust

grounding conductor and a grounding

the

screw

labeledN in

the

terminal

plug. The

plug

must

be

plugged

into

airn outlet

on

the

rear

of

the

appliance.

block.

appropriate

outlet which

has been

To

take

account

of

the

spatial

5.

Thread

the

3owire cable through

properly installed and grounded in

requirements

and

an existing

exhaust

the

U.L.

strain

relief clamp.

6.

accordance

with

all

local

regulations

air system, the following connection

Tighten

the

screws (2.5 Nm) on theand ordinances.

options are possible for the exhaust air

U.L. strain relief clamp so that the

outlet:

power

cord cannot

be moved.

d WARNING

d

-

on

right

side

of the

appliance,

-

on

the

underside

of

the

appliance.

		Improper		connection		of	the
		equipment			grounding	conductor
		may	result		in electric shock.
8. Tighten all 3 screws (3 Nm) so	that	Have	the		appliance	checked by
the power conductors are held	in	a qualified			electrician	or	service
place securely.		technician			if you are in		doubt as
		to whether the dryer has been
		properly		grounded.

2

1

3

1 Y Exhaust air outlet on the rear of the appliance (standard)

7