Maytag W105623338C-SP Dryer Care, Cleaning the Dryer Location, Cleaning the Dryer Interior

Page 12

DRYER CARE

CLEANING THE DRYER LOCATION

Keep dryer area clear and free from items that would block the air flow for proper dryer operation. This includes clearing piles of laundry in front of the dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum

1.Use a mild hand dish detergent mixed at a low concentration with very warm water, and rub with a soft cloth.

2.Rinse well with a wet sponge or towel.

3.Tumble a load of clean clothes or towels to dry drum

OR

Use a microfiber cloth and hot water in a spray bottle to clean the drum and a second microfiber towel to dry.

NOTE: Items that contain unstable dyes, such as denim blue jeans or brightly colored cotton items, may discolor the rear of the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to avoid transfer of dye.

REMOVING ACCUMULATED LINT

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualified appliance servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending on dryer usage.

CLEANING THE LINT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer. The control panel has an indicator light to remind you to clean the lint screen after each load. A screen blocked by lint will increase drying time.

To clean:

1.Pull the lint screen straight up. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.

2.Push the lint screen firmly back into place.

IMPORTANT:

nDo not run the dryer with the lint screen loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.

nIf lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See “Venting Requirements” in the Installation Instructions.

As needed cleaning

Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup.

To wash:

1.Roll lint off the screen with your fingers.

2.Wet both sides of lint screen with hot water.

3.Wet a nylon brush with

hot water and liquid detergent. Scrub lint screen with the brush

to remove residue buildup.

4. Rinse screen with hot water.

5.Thoroughly dry lint screen with a clean towel. Reinstall screen in dryer.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents ET D’ENTRETIEN Dryer Safety Page Check Your Vent System for Good AIR Flow Remove lint and debris from the exhaust hoodClear away items from in front of the dryer Control Panel and Features Not all features and cycles are available on all modelsTemp Level Load. See Cycle Guide for detailed descriptions of cyclesBulky cycle Airflow Cycle Signal Use this button to turn the signal indicating the end of aButton is pressed. Press and hold the Cycle Signal button Not all cycles and options are available on all modelsDrying Dryness Default Available Items to dry Cycle Guide Sensor CyclesUse Sensor Cycles for better fabric care and energy savings Cycle DetailsWhen you select a Timed Cycle Cycle Guide Timed CyclesCycle Guide Steam Cycles Maximum dry time is 100 minutesUsing Your Dryer Press the POWER/CANCEL button to turn on the dryerTo change the drying settings It cannot be changed without stopping the cycleTimed Cycles Select the Wrinkle PreventAdditional Features Using the Drying RackChanging the Drum Light To use the drying rackCleaning the Dryer Location Cleaning the Dryer InteriorCleaning the Lint Screen Dryer CareNON-USE, STORAGE, and Moving Care Special Instructions For Steam ModelsTroubleshooting Water inlet valve on dryer is runningWith Steam cycle selected Separate the load items and restart the dryer127 mm. See Installation Instructions Changing the Sensor Cycle settings to increase drying timeAt the end of the cycle GarmentsReplace the fuse or reset the circuit breaker Check Vent indicator is lit Lint screen or vent is cloggedLow or no line voltage Instructions for detailsMaytag Laundry Limited Warranty Sécurité DE LA Sécheuse Page Page Nettoyer le filtre à charpie avant chaque charge Retirer la charpie et les résidus du clapet d’évacuationDégager tout article qui se trouverait devant la sécheuse Ne peut pas être ajustée manuellementTableau DE Commande ET Caractéristiques Bouton POWER/CANCEL mise sous tension/annulationBouton START/PAUSE mise en marche/pause Niveau de températureDrum Light lampe du tambour Steam boost sur certains modèlesLes programmes Airflow circulation d’airGuide DE Programmes Programmes DE Détection Niveau deOptions Détails du programme Guide DE Programmes Programmes Minutés Guide DE Programmes Programmes Avec VapeurUtilisation DE LA Sécheuse Cet appareilProgrammes de détection Rafraîchissement personnalisé avec vapeurPour changer les réglages de séchage Utilisation DE LA Grille DE Séchage Changement DE L’AMPOULE DU TambourUtilisation de la grille de séchage Changement de l’ampoule du tambourNettoyage DE L’EMPLACEMENT DE LA Sécheuse Entretien DE LA SécheuseNettoyage DE L’INTÉRIEUR DE LA Sécheuse Retirer LA Charpie AccumuléeInstructions Spéciales Pour LES Modèles Vapeur Dépannage ’installation Lourde pour sécher rapidementObstruent la grille SuiteCode de diagnostic ’installation pour plus de détailsCodes de service La sécheuse doit être réparée Des odeurs persistent dansTambour parois latérales uniquement Moteur d’entraînement Être facilement identifiésExonération DE Responsabilité EN Dehors DE LA Garantie Page Page Page You can write with any questions or concerns at Vous pouvez écrire en soumettant toute question
Top Page Image Contents