Maytag W105623334C NON-USE, STORAGE, and Moving Care, Special Instructions For Steam Models

Page 13

NON-USE, STORAGE, AND MOVING CARE

Install and store your dryer where it will not freeze. Because some water may stay in the hose, freezing can damage your dryer. If storing or moving your dryer during freezing weather, winterize it.

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:

1.Unplug dryer or disconnect power.

2.Clean lint screen. See “Cleaning the Lint Screen.”

3.Turn off the water supply to the dryer. This helps to avoid unintended flooding (due to a water pressure surge) while you are away.

Moving Care

For power supply cord-connected dryers:

1.Unplug the power supply cord.

2.Gas models only: Close shut-off valve in gas supply line.

3.Gas models only: Disconnect gas supply line pipe and remove fittings attached to dryer pipe.

4.Gas models only: Cap the open gas supply line.

5.Steam models only: Shut off water faucet.

6.Steam models only: Disconnect the water inlet hose from faucet; then drain the hose. Transport hose separately.

7.Make sure leveling legs are secure in dryer base.

8.Use tape to secure dryer door.

For direct-wired dryers:

1.Disconnect power.

2.Disconnect wiring.

3.Steam models only: Shut off water faucet.

4.Steam models only: Disconnect the water inlet hose from faucet; then drain the hose. Transport hose separately.

5.Make sure leveling legs are secure in dryer base.

6.Use tape to secure dryer door.

Reinstalling the Dryer

Follow the Installation Instructions to locate, level, and connect the dryer.

SPECIAL INSTRUCTIONS

FOR STEAM MODELS

Water Inlet Hose

Replace inlet hose and hose screen after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hose if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hose, record the date of replacement.

To Winterize the Dryer

1.Unplug dryer or disconnect power.

2.Shut off water faucet.

3.Disconnect water inlet hose from faucet and drain.

To Use the Dryer Again

1.Flush water pipes. Reconnect water inlet hose to faucet. Turn on water faucet.

2.Plug in dryer or reconnect power as described in the Installation Instructions.

13

Image 13

Contents ET D’ENTRETIEN Dryer Safety Page Remove lint and debris from the exhaust hood Check Your Vent System for Good AIR FlowClear away items from in front of the dryer Not all features and cycles are available on all models Control Panel and FeaturesTemp Level Load. See Cycle Guide for detailed descriptions of cyclesUse this button to turn the signal indicating the end of a Bulky cycle Airflow Cycle SignalButton is pressed. Press and hold the Cycle Signal button Not all cycles and options are available on all modelsCycle Guide Sensor Cycles Drying Dryness Default Available Items to dryUse Sensor Cycles for better fabric care and energy savings Cycle DetailsCycle Guide Timed Cycles When you select a Timed CycleCycle Guide Steam Cycles Maximum dry time is 100 minutesPress the POWER/CANCEL button to turn on the dryer Using Your DryerIt cannot be changed without stopping the cycle To change the drying settingsTimed Cycles Select the Wrinkle PreventUsing the Drying Rack Additional FeaturesChanging the Drum Light To use the drying rackCleaning the Dryer Interior Cleaning the Dryer LocationCleaning the Lint Screen Dryer CareSpecial Instructions For Steam Models NON-USE, STORAGE, and Moving CareWater inlet valve on dryer is running TroubleshootingWith Steam cycle selected Separate the load items and restart the dryerChanging the Sensor Cycle settings to increase drying time 127 mm. See Installation InstructionsAt the end of the cycle GarmentsCheck Vent indicator is lit Lint screen or vent is clogged Replace the fuse or reset the circuit breakerLow or no line voltage Instructions for detailsMaytag Laundry Limited Warranty Sécurité DE LA Sécheuse Page Page Retirer la charpie et les résidus du clapet d’évacuation Nettoyer le filtre à charpie avant chaque chargeDégager tout article qui se trouverait devant la sécheuse Ne peut pas être ajustée manuellementBouton POWER/CANCEL mise sous tension/annulation Tableau DE Commande ET CaractéristiquesBouton START/PAUSE mise en marche/pause Niveau de températureSteam boost sur certains modèles Drum Light lampe du tambourLes programmes Airflow circulation d’airNiveau de Guide DE Programmes Programmes DE DétectionOptions Détails du programme Guide DE Programmes Programmes Avec Vapeur Guide DE Programmes Programmes MinutésCet appareil Utilisation DE LA SécheuseRafraîchissement personnalisé avec vapeur Programmes de détectionPour changer les réglages de séchage Changement DE L’AMPOULE DU Tambour Utilisation DE LA Grille DE SéchageUtilisation de la grille de séchage Changement de l’ampoule du tambourEntretien DE LA Sécheuse Nettoyage DE L’EMPLACEMENT DE LA SécheuseNettoyage DE L’INTÉRIEUR DE LA Sécheuse Retirer LA Charpie AccumuléeInstructions Spéciales Pour LES Modèles Vapeur Dépannage Lourde pour sécher rapidement ’installationObstruent la grille Suite’installation pour plus de détails Code de diagnosticCodes de service La sécheuse doit être réparée Des odeurs persistent dansÊtre facilement identifiés Tambour parois latérales uniquement Moteur d’entraînementExonération DE Responsabilité EN Dehors DE LA Garantie Page Page Page Vous pouvez écrire en soumettant toute question You can write with any questions or concerns at