Maytag W105623338C-SP Low or no line voltage, Replace the fuse or reset the circuit breaker

Page 16

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.maytag.com/product_help –

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

If you experience

Possible Causes

Solution

Dryer Results (cont.)

 

 

Load too hot

Load removed before cool down

Allow the dryer to complete the cool down portion of the cycle

portion of cycle complete.

before removing the load.

Using Timed Dry Cycle with a high

Select a Sensor cycle with a lower heat setting to avoid overdrying

temperature setting.

the load.

Dryer Displaying Code Message or Indicator Is Lit

“PF” (power failure)

The drying cycle has been interrupted

Press and hold START/PAUSE to resume the cycle, or press

 

by a power failure.

POWER to select a new cycle.

“L2” Diagnostic Code

There may be a problem with your

The dryer will continue to run when this diagnostic code is present.

(low or no line voltage

home power supply keeping the dryer’s

Press any key to clear the code from the display and return to the

condition)

heater from turning on.

estimated time remaining.

 

 

Try the following:

 

 

• Check to see if a household fuse has blown or circuit breaker

 

 

has tripped. Electric dryers use two household fuses or breakers.

 

 

Replace the fuse or reset the circuit breaker.

 

 

• Confirm the power cord is properly installed. Refer to Installation

 

 

Instructions for details.

 

 

Select a Timed Dry heated cycle, and restart the dryer.

 

 

If the message persists, consult a qualified electrician.

Check Vent indicator is lit

The lint screen or vent is clogged; the

The dryer will continue to run when this diagnostic code is present.

 

vent is crushed, kinked or has too many

Touch any key to clear the code from the display and return to the

 

turns.

estimated time remaining.

 

 

Try the following:

 

 

• Clean lint screen.

 

 

• Check to see if the vent run from the dryer to the wall is

 

 

crushed or kinked.

 

 

• Confirm that the vent run from the dryer to the wall is free

 

 

of lint and debris.

 

 

• Confirm that the exterior vent exhaust hood is free of lint

 

 

and debris.

 

 

• Confirm that your vent system falls within the recommended

 

 

run length and number of elbows for the type of vent you are using.

 

 

Refer to “Plan Vent System” in the Installaton Instructions for

 

 

details.

 

 

Select a Timed Dry heated cycle, and restart the dryer.

 

 

If the message persists, have your entire home venting run cleaned.

 

 

Contact a venting specialist.

“F# E#” (F1 E1, F3 E1,

The dryer is in need of service.

If a code beginning with an “F” appears in the display, alternating

etc.) variable service

 

between F# and E#, the dryer control has detected a problem that

codes

 

requires service. Call for service.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents ET D’ENTRETIEN Dryer Safety Page Remove lint and debris from the exhaust hood Check Your Vent System for Good AIR FlowClear away items from in front of the dryer Control Panel and Features Not all features and cycles are available on all modelsTemp Level Load. See Cycle Guide for detailed descriptions of cyclesBulky cycle Airflow Cycle Signal Use this button to turn the signal indicating the end of aButton is pressed. Press and hold the Cycle Signal button Not all cycles and options are available on all modelsDrying Dryness Default Available Items to dry Cycle Guide Sensor CyclesUse Sensor Cycles for better fabric care and energy savings Cycle DetailsWhen you select a Timed Cycle Cycle Guide Timed CyclesCycle Guide Steam Cycles Maximum dry time is 100 minutesUsing Your Dryer Press the POWER/CANCEL button to turn on the dryerTo change the drying settings It cannot be changed without stopping the cycleTimed Cycles Select the Wrinkle PreventAdditional Features Using the Drying RackChanging the Drum Light To use the drying rackCleaning the Dryer Location Cleaning the Dryer InteriorCleaning the Lint Screen Dryer CareNON-USE, STORAGE, and Moving Care Special Instructions For Steam ModelsTroubleshooting Water inlet valve on dryer is runningWith Steam cycle selected Separate the load items and restart the dryer127 mm. See Installation Instructions Changing the Sensor Cycle settings to increase drying timeAt the end of the cycle GarmentsReplace the fuse or reset the circuit breaker Check Vent indicator is lit Lint screen or vent is cloggedLow or no line voltage Instructions for detailsMaytag Laundry Limited Warranty Sécurité DE LA Sécheuse Page Page Nettoyer le filtre à charpie avant chaque charge Retirer la charpie et les résidus du clapet d’évacuationDégager tout article qui se trouverait devant la sécheuse Ne peut pas être ajustée manuellementTableau DE Commande ET Caractéristiques Bouton POWER/CANCEL mise sous tension/annulationBouton START/PAUSE mise en marche/pause Niveau de températureDrum Light lampe du tambour Steam boost sur certains modèlesLes programmes Airflow circulation d’airNiveau de Guide DE Programmes Programmes DE DétectionOptions Détails du programme Guide DE Programmes Programmes Minutés Guide DE Programmes Programmes Avec VapeurUtilisation DE LA Sécheuse Cet appareilProgrammes de détection Rafraîchissement personnalisé avec vapeurPour changer les réglages de séchage Utilisation DE LA Grille DE Séchage Changement DE L’AMPOULE DU TambourUtilisation de la grille de séchage Changement de l’ampoule du tambourNettoyage DE L’EMPLACEMENT DE LA Sécheuse Entretien DE LA SécheuseNettoyage DE L’INTÉRIEUR DE LA Sécheuse Retirer LA Charpie AccumuléeInstructions Spéciales Pour LES Modèles Vapeur Dépannage ’installation Lourde pour sécher rapidementObstruent la grille SuiteCode de diagnostic ’installation pour plus de détailsCodes de service La sécheuse doit être réparée Des odeurs persistent dansTambour parois latérales uniquement Moteur d’entraînement Être facilement identifiésExonération DE Responsabilité EN Dehors DE LA Garantie Page Page Page You can write with any questions or concerns at Vous pouvez écrire en soumettant toute question
Top Page Image Contents