Maytag W105623334C 127 mm. See Installation Instructions, At the end of the cycle, Garments

Page 15

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.maytag.com/product_help –

In Canada www.maytag.ca for assistance and to possibly avoid a service call.

If you experience

Possible Causes

Solution

 

 

 

Dryer Results

 

 

Clothes are not drying

Fabric softener sheets are blocking

The air outlet grille is just inside the door, behind the lint screen.

satisfactorily or drying

the grille.

Check that it is not blocked by a fabric softener sheet. Use only one

times are too long (cont.)

 

fabric softener sheet, and use it only once.

 

The dryer is located in a room with

Proper operation of dryer cycles requires temperatures above

 

temperature below 45ºF (7ºC).

45ºF (7ºC).

 

The dryer is located in a closet.

Closet doors must have ventilation openings at the top and bottom

 

 

of the door. The front of the dryer requires a minimum of 1" (25 mm)

 

 

of airspace, and, for most installations, the rear of the dryer requires

 

 

5" (127 mm). See Installation Instructions.

Cycle time is too short

The load may not be contacting the

Level the dryer. See Installation Instructions. All four dryer feet

 

sensor strips on Sensor Cycles.

should be in firm contact with the floor.

 

Clothes are coming out of the Steam

Under certain environmental or installation conditions you may

 

cycles with damp or wet spots.

experience underdrying. Select the Custom Refresh cycle. Then

 

 

select the appropriate number of garments for the load from the

 

 

Number of Garments option.

 

The Sensor Cycles are ending early.

Change the dryness level setting on Sensor Cycles. Increasing

 

 

or decreasing the dryness level will change the amount of drying

 

 

time in a cycle. If loads are consistently ending too early, see also

 

 

“Changing the Sensor Cycle settings to increase drying time.”

Lint on load

Lint screen is clogged with lint.

Clean lint screen before each load.

Stains on load

Improper use of fabric softener.

Add dryer fabric softener sheets at the beginning of the cycle.

 

 

Fabric softener sheets added to a partially dried load can stain your

 

 

garments. Do not use fabric softener sheets with Steam Cycles.

Stains on drum

Loose dyes in clothes.

Drum stains are caused by dyes in clothing (usually blue jeans).

 

 

These will not transfer to other clothing.

Loads are wrinkled

The load was not removed from dryer

Select Auto or Custom Refresh cycles (on some models) to tumble

 

at the end of the cycle.

the load with water and heat. These cycles are best for smoothing

 

 

out wrinkles and reducing odors from loads consisting of wrinkle-

 

 

free cotton, cotton polyester blends, common knits, and synthetic

 

 

garments.

 

 

NOTE: Refer to garment care label instructions. Dry clean only

 

 

garments are not recommended.

 

The dryer was overloaded.

Dry smaller loads that can tumble freely. When using the Custom

 

 

Refresh cycle, be sure to select the correct number of garments to

 

 

be refreshed. Results may also vary depending on fabric type. This

 

 

cycle is best for reducing wrinkles and odors from loads consisting

 

 

of wrinkle-free cotton, cotton polyester blends, common knits, and

 

 

synthetics.

 

For steam cycles, the water is not

Make sure water is connected to the dryer. Check that water inlet

 

properly connected with the dryer.

hose is connected to both the faucet and dryer’s water inlet valve.

 

 

Check that the water supply is turned on.

Odors

Recent painting, staining, or varnishing

Ventilate the area. When the odors or fumes are gone from the area,

 

in the area where your dryer is located.

rewash and dry the clothing.

 

For Steam Cycles, the water is not

Make sure water is connected to the dryer. Check that water inlet

 

properly connected with the dryer.

hose is connected to both the faucet and dryer’s water inlet valve.

 

 

Check that the water supply is turned on.

 

Odors are left in garments after

To remove odors left in garments after wearing, select Auto Refresh

 

wearing.

(on some models). This cycle is best for reducing wrinkles and

 

 

odors from loads consisting of wrinkle-free cotton, cotton polyester

 

 

blends, common knits, and synthetics.

15

Image 15
Contents ET D’ENTRETIEN Dryer Safety Page Check Your Vent System for Good AIR Flow Remove lint and debris from the exhaust hoodClear away items from in front of the dryer Load. See Cycle Guide for detailed descriptions of cycles Control Panel and FeaturesNot all features and cycles are available on all models Temp LevelNot all cycles and options are available on all models Bulky cycle Airflow Cycle SignalUse this button to turn the signal indicating the end of a Button is pressed. Press and hold the Cycle Signal buttonCycle Details Drying Dryness Default Available Items to dryCycle Guide Sensor Cycles Use Sensor Cycles for better fabric care and energy savingsMaximum dry time is 100 minutes When you select a Timed CycleCycle Guide Timed Cycles Cycle Guide Steam CyclesPress the POWER/CANCEL button to turn on the dryer Using Your DryerSelect the Wrinkle Prevent To change the drying settingsIt cannot be changed without stopping the cycle Timed CyclesTo use the drying rack Additional FeaturesUsing the Drying Rack Changing the Drum LightDryer Care Cleaning the Dryer LocationCleaning the Dryer Interior Cleaning the Lint ScreenSpecial Instructions For Steam Models NON-USE, STORAGE, and Moving CareSeparate the load items and restart the dryer TroubleshootingWater inlet valve on dryer is running With Steam cycle selectedGarments 127 mm. See Installation InstructionsChanging the Sensor Cycle settings to increase drying time At the end of the cycleInstructions for details Replace the fuse or reset the circuit breakerCheck Vent indicator is lit Lint screen or vent is clogged Low or no line voltageMaytag Laundry Limited Warranty Sécurité DE LA Sécheuse Page Page Ne peut pas être ajustée manuellement Nettoyer le filtre à charpie avant chaque chargeRetirer la charpie et les résidus du clapet d’évacuation Dégager tout article qui se trouverait devant la sécheuseNiveau de température Tableau DE Commande ET CaractéristiquesBouton POWER/CANCEL mise sous tension/annulation Bouton START/PAUSE mise en marche/pauseAirflow circulation d’air Drum Light lampe du tambourSteam boost sur certains modèles Les programmesGuide DE Programmes Programmes DE Détection Niveau deOptions Détails du programme Guide DE Programmes Programmes Avec Vapeur Guide DE Programmes Programmes MinutésCet appareil Utilisation DE LA SécheuseRafraîchissement personnalisé avec vapeur Programmes de détectionPour changer les réglages de séchage Changement de l’ampoule du tambour Utilisation DE LA Grille DE SéchageChangement DE L’AMPOULE DU Tambour Utilisation de la grille de séchageRetirer LA Charpie Accumulée Nettoyage DE L’EMPLACEMENT DE LA SécheuseEntretien DE LA Sécheuse Nettoyage DE L’INTÉRIEUR DE LA SécheuseInstructions Spéciales Pour LES Modèles Vapeur Dépannage Suite ’installationLourde pour sécher rapidement Obstruent la grilleDes odeurs persistent dans Code de diagnostic’installation pour plus de détails Codes de service La sécheuse doit être réparéeÊtre facilement identifiés Tambour parois latérales uniquement Moteur d’entraînementExonération DE Responsabilité EN Dehors DE LA Garantie Page Page Page Vous pouvez écrire en soumettant toute question You can write with any questions or concerns at