Maytag W105623338C-SP Not all cycles and options are available on all models, Check Lint Screen

5	CYCLE OPTIONS	6	LED DISPLAY AND SETTINGS BUTTONS
	Use these buttons to select available options for your dryer.		When you select a cycle, its default settings will light up and
	Not all cycles and options are available on all models.		the Estimated Time Remaining (for Sensor Cycles) or actual
	Wrinkle Prevent/Wrinkle Prevent with Steam		time remaining (for Timed Cycles) will be displayed.
			Use the buttons along the bottom of the display to adjust
	(on some models)
			settings. See “Cycle Guide” for available settings on each
	If you will be unable to remove a load immediately, press
			cycle. Not all settings are available with all cycles.
	Wrinkle Prevent to add up to 150 minutes of periodic
	tumbling to help reduce wrinkling. On models with Wrinkle
	Prevent with Steam, a short steam cycle is added after
	60 minutes to help smooth out wrinkles.
	Drum Light
	Press to turn the drum light on or off. The light will also turn
	on when the door is open, and turn off automatically after
	about 5 minutes.
	Damp Dry Signal
	When selected, a signal will sound during the drying
	cycle when the load is damp but not completely dry. This
	will allow you to take clothes out of the load that do not
	need to dry completely. This option is available on Heavy
	Duty, Normal, Denim, Bulky, Wrinkle Control, Sheets, Active
	Wear, Towels and Delicate cycles.		Steam model shown
	NOTE: The Damp Dry signal defaults to “ON” when using
	the Bulky cycle.		Airflow
	Cycle Signal		This indicator will show the status of airflow through the dryer
			during Sensor cycles. The Detecting light comes on during
	Use this button to turn the signal indicating the end of a
			the sensing phase at the beginning of cycle. The Good light
	drying cycle on or off, or to adjust the volume of the signal.
			will come on if no major vent blockage is detected. The Check
	NOTE: You may also turn off the tones that sound when a
			Vent light will come on if a blocked vent or low airflow issue is
	button is pressed. Press and hold the Cycle Signal button		detected. For more information on maintaining good airflow,
	for about three seconds to turn button sounds on or off.		see “Check Your Vent System for Good Airflow”. The Airflow
	Reduce Static (on some models)		sensing feature is available for Sensor cycles only.
			NOTE: If there are other error issues during a cycle, the
	Press to add the Reduce Static option to selected Sensor
	cycles (see Cycle Guide). The dryer will automatically		Airflow indicator will not light up. See “Dryer Displaying Code
	tumble, pause, and introduce a small amount of moisture		Message” in “Troubleshooting” section.
	into the load to help reduce static. This option adds		Steam (on some models)
	approximately 8 minutes to the total cycle time.
			This indicator will light when the Steam function is active.
	Steam Boost (on some models)
			NOTE: Steam options are not available on all models or on
	Steam Boost adds steam to the end of the Heavy Duty,		all cycles.
	Bulky, Normal, Sheets, Towels, or Denim cycle to help		Done
	smooth wrinkles.
			This will indicate that the selected cycle has ended and the

load may be removed from the dryer. If the Wrinkle Prevent option has been selected, the dryer may continue to tumble the load, even if the DONE indicator is lit.

Check Lint Screen

The Check Lint Screen indicator will light when the drying cycle is complete as a reminder to clean the lint screen.

Wrinkle Prevent

This indicator will light if the Wrinkle Prevent option has been selected and is running. The dryer will continue to periodically tumble the load for up to 150 minutes (depending on model and selected settings) after the cycle has ended.

6