Mitsubishi Electronics FR-A500L instruction manual 201

PARAMETERS

Func-		Parameter			Minimum	Factory Setting	Refer To
			Name	Setting Range	Setting		Page:
tion		Number
					Increments		<Note9>
		200	Programmed operation minute/second	0 to 3	1	0	131
			selection
operation			Program set 1	0 to 2: Rotation direction	1	0
		201		0 to 400, 9999:Frequency	0.1Hz	9999	131
			1 to 10
				0 to 99.59: Time	Minute or second	0
Programmed		221	Program set 2	0 to 2: Rotation direction	1	0	131
				0 to 400, 9999:Frequency	0.1Hz	9999
		211	11 to 20	0 to 400, 9999:Frequency	0.1Hz	9999	131
				0 to 99.59: Time	Minute or second	0
			Program set 3	0 to 2: Rotation direction	1	0
			21 to 30	0 to 99.59: Time	Minute or second	0
		231	Timer setting	0 to 99.59		0	131
operation		232	Multi-speed setting (speed 8)	0 to 400Hz, 9999	0.01Hz	9999	135
		233	Multi-speed setting (speed 9)	0 to 400Hz, 9999	0.01Hz	9999	135
		234	Multi-speed setting (speed 10)	0 to 400Hz, 9999	0.01Hz	9999	135
speed-Multi		235	Multi-speed setting (speed 11)	0 to 400Hz, 9999	0.01Hz	9999	135
		236	Multi-speed setting (speed 12)	0 to 400Hz, 9999	0.01Hz	9999	135
		237	Multi-speed setting (speed 13)	0 to 400Hz, 9999	0.01Hz	9999	135
		238	Multi-speed setting (speed 14)	0 to 400Hz, 9999	0.01Hz	9999	135
		239	Multi-speed setting (speed 15)	0 to 400Hz, 9999	0.01Hz	9999	135
functions		240	Soft-PWM setting	0, 1	1	1	135
Sub		244	Cooling fan operation selection	0, 1	1	0	135
selectionStop	function	250	Stop selection	0 to 100 sec, 9999	0.1 sec	9999	135
Sub	functions	251	Start holding time	0 to 10 sec, 9999	0.1 sec	9999	136
function		261	Power failure stop selection	0, 1	1	0	137
		262	Subtracted frequency at deceleration	0 to 20Hz	0.01Hz	3Hz	137
			start
stop		263	Subtraction starting frequency	0 to 120Hz, 9999	0.01Hz	60Hz<50Hz>	137
		264	Power-failure deceleration time 1	0 to 3600/	0.1 sec/	5 sec	137
failure				0 to 360 sec	0.01 sec
		265	Power-failure deceleration time 2	0 to 3600/	0.1 sec/	9999	137
Power				0 to 360 sec, 9999	0.01 sec
		266	Power-failure deceleration time switch-	0 to 400Hz	0.01Hz	60Hz	137
			over frequency
Selection	function	270	Stop-on-contact/load torque high-speed	0, 1, 2, 3	1	0	139
			frequency control selection
speed-High frequency control		271	High-speed setting maximum current	0 to 200%	0.1%	50%	140
		272	Mid-speed setting minimum current	0 to 200%	0.1%	100%	140
		273	Current averaging range	0 to 400Hz, 9999	0.01Hz	9999	140
		274	Current averaging filter constant	1 to 4000	1	16	140
Stopon	contact	275	Stop-on-contact exciting current low-	0 to 1000%, 9999	1%	9999	143
			speed multiplying factor (Note 5)
		276		0, 1, 2, 9999	1	9999	143
			Stop-on-contact PWM carrier frequency
			(Note 5)

22