Mitsubishi Electronics FR-A500L Main circuit error E,15 details, Charge Alarm, Name Details

Page 38

PROTECTIVE FUNCTIONS

Main circuit error [E,15] details

A500

There are two 7-segment LEDs on the right of the operation panel as shown on the right. The following fault details are indicated by the LED display.

CHARGE

ALARM

Left LED

Brake unit cooling fin overheating

Control board ambient temperature error

Output overcurrent

Right LED

Cooling

fan power Capacitor Cooling fin

supply overcurrent overheat error

Gate power

supply error

For example, if the display is	, the output overcurrent , capacitor overcurrent and gate power supply
errors have occurred.

	Name	Details

	Brake unit cooling fin overheating	The inverter output will stop if the brake unit's cooling fin temperature rises above the
	Brake unit cooling fin overheating	specified value.
		specified value.

	Control board ambient temperature error	The inverter output will stop if the ambient temperature of the control board rises above
	Control board ambient temperature error	the specified value.
		the specified value.

	Output overcurrent	The inverter output will stop if the inverter's output current flows above the specified
	Output overcurrent	value.
		value.

	Cooling fan power supply error	The inverter output will stop if the cooling fan's power drops below the specified value.

	Capacitor overcurrent	The inverter will stop if a current exceeding the specified value flows to the main circuit
	Capacitor overcurrent	smoothing capacitor.
		smoothing capacitor.

	Cooling fin overheat	The inverter output will stop if the cooling fin's temperature rises above the specified
	Cooling fin overheat	value.
		value.

	Gate power supply error	The inverter output will stop if the gate power supply voltage drops below the specified
	Gate power supply error	value.
		value.

27

Image 38

Contents FR-A500L This section is specifically about safety matters Injury Prevention Electric Shock PreventionFire Prevention Additional instructions Transportation and installationWiring Trial runEmergency stop Maintenance, inspection and parts replacementOperation Disposing of the inverterContents Chapter Outline Wiring Precautions for operationInstallation Pre-Operation InformationNFB ELB Basic ConfigurationBasic configuration Name DescriptionChapter Installation Instructions for installationAt 5cm 1.97 inch Wiring Terminal connection diagramDescription of control circuit terminals Symbol Terminal Name DescriptionDescription of main circuit terminals Terminal Name DescriptionIPF ，B，CRUN Wiring of the main circuit Wiring instructionsTerminal block layout 800 2300P1, P, N Connection of the power supply and motor Connection procedureWiring of the control circuit NA version（OR Version）Changing the control logic RUN DC24V How to use terminals STOP, CS and PC Connection to the PU connector For RS-485 communicationDesign information Chapter Operation Chapter Parameters Parameter List ParametersDU/PU main display data selection F4 fourth frequency voltage 173 201 Can be accessed when Pr = Protective Functions Operation Parameter Errors AlarmsError alarm definitions Unit Name DescriptionSTP OHTOLT OPTCTE MB7Name Details Main circuit error E,15 detailsCharge Alarm To know the operating status at the occurrence of alarm Correspondences between digital and actual charactersAlarm Code Alarm Output across B-C FR-DU04 Alarm code outputResetting the inverter Operation PanelOperation Panel Check Point Remedy Display TroubleshootingChecking the operation panel display at alarm stop Check Point Remedy Motor remains stopped Faults and check pointsSpeed greatly differs from the setting Motor rotates in opposite directionMotor current is large Operation mode is not changed properlyPower lamp is not lit Speed does not increaseCheck items Precautions for Maintenance and InspectionPrecautions for maintenance and inspection Periodic inspectionInsulation resistance test using megger Dielectric strength testDaily and Periodic Inspection Description Method Criterion Instrument DailyModule device numbers and terminals to be checked PreparationChecking method Smoothing capacitors Replacement of partsCooling fan RelaysMeasurement of main circuit voltages, currents and power Measurement of voltages and currents5VDC Measuring Point Measuring Instrument10VDC Chapter Specifications Standard specification Model specificationsCommon specifications Alarm FR-PU04Outline drawings FR-A540L-450K, 375KFR-A540L-540K～800K SDA P5S RDB RDA SDBAppendices Front AppendixAppendix EF-40ETB R G Converter EF-30ETB Control Inverter Wiring between cooling fan and terminals is as followsCheck the air flow direction Resistor Temperature Abnormal Signals MT-BR5MT-BR5 TH1 TH2 PR PR EShipment case example

Related manuals

Manual 64 pages 26.15 Kb