AEG 8000012364 BAL Operation, Output voltage ok, Input undervoltage UE, Input overvoltage UE

Page 32

"UniVert 2" inverter

Messages	- Operation
	LED green
	- Output voltage ok
	LED green
	- Input undervoltage UE<
	LED red
	- Input overvoltage UE>
	LED red
	- Fault
	LED red
	- Overtemperature ϑ>
	LED red
	- Collective fault
	LED red
Remote signals (X3)	Operation and collective fault
	message via potential-free relay
	contact (safe isolation).
	Max. contact load:
	150 V DC < 1.6 A
	Min. contact load: 12 V 0.1 A
Monitoring systems	- INV output undervoltage
	- INV output overvoltage
	- DC undervoltage
	- DC overvoltage
	- Heat sink overtemperature
	- Overload / short circuit
	- Self-test, watchdog
	- Internal auxiliary voltages
	- Individual set fault, K7 fault
Design	19" mounting rail for installation in
	module rack in acc. with
	DIN 41494
Protection class	IP 20
Cooling	Forced air cooling
Intake air temperature	With Uo = 230 VAC, rated current
	and cos ϕ = 0.8
	0°C to 45°C,
	measured below the inverter
Storage temperature	-20°C to +70°C
Ambient conditions	IEC 721 Part 3-3 Class 3K3 / 3Z1 /
	3B1 / 3C2 / 3S2 / 3M2
Site altitude	Up to 2000 m above sea level

Page 32 of 42

8000012364 BAL, en

Image 32

Contents Operating Instructions UniVert 2 inverter and SBS option Warranty Duty to Provide InformationValidity HandlingCopyright AbbreviationsHotline Table of Contents Dimensional Drawing Maintenance TroubleshootingTechnical Data Accident Prevention Regulations Safety InstructionsImportant Instructions and Explanations Qualified Personnel Safety Awareness ApplicationLiability DirectivesGeneral Information System DescriptionFunction of the System Individual INV operationParallel INV operation Individual or parallel operation with SBSParallel INV operation Block diagram of the inverter Description of the INVPrinciple of Operation of the INV, Electrical Description of the SBS SBSPrinciple of Operation of the SBS, Electrical Function of the Inverter ON/OFF Switch DIL SwitchCan Bus Interfaces X6 S2.1 S2.2 S2.3Switches S2.4, S2.5 and S2.6 Own Address INV Switches S2.7 and S2.8 Number of redundant INVsINVs Settings must be the same on all INVs and the SBS S2.4 S2.5 S2.6 AddressSignalling, Displays and Remote Signals Display Colour Operating statusOperating Statuses Switchback AttemptsFunction of the SBS optional Reset Button AC Mains InputAC Busbar AC Mains Monitoring SystemS3.1 S3.2 S3.3 S3.7 S3.8 INVs Operating modes Assignment of the signal terminalsSwitchover without gap Switchover with gap Installation Connecting the Loads / DC / MainsStart-Up ConnectionDisconnection Maintenance For systems with SBS additionally TroubleshootingOutput Voltage Deviation Technical Data General Data INVFault Overtemperature ϑCollective fault OperationGeneral Data SBS With safe isolation at UO ≤ 60 V DC UniVert 2 inverter Electrical Data At 24 Type E-number G110 E230/10,9/2rfg-CFp2,5 3000000263 Type E-number E230 E230/115/2-VFp26,5-8 3000000646 Dimensional Drawing Inverter dimensions type 1.5 and 3.3 kVAInverter dimensions type 2.5 kVA SBS dimensions