Korg D8 manual Edit Play Mode, Trigger, P1 Pre roll time setting, P2 Post roll time setting

Page 51

8. EDIT PLAY MODE

P1 Pre roll time setting

Here you can specify the pre roll time that is added to the IN time of Auto Play On and Auto Repeat On

when Auto Punch In/Out is performed.

When Auto Play On or Auto Repeat On is used in con- junction with Auto Punch In/Out, you will be able to listen for the pre roll time before punch in occurs, allowing you to prepare to start recording.

1 2

PreRol:02M

P1-1

Pre roll time numerical setting

[00...10]

P1-2

Pre roll time unit select

[M, s]

Specifies the pre roll time in either measures or sec- onds.

In P1-1 you can specify a numerical value (00–10), and in P1-2 you can select either M (measure) or s (second) units. When you change the pre roll time unit, the post roll time unit will change automatically. When M is selected, the maximum pre roll time is 10 measures. When s is selected, the maximum is 10 seconds.

When the power is turned on, the pre roll time and post roll time are automatically set to 02M.

P2 Post roll time setting

Here you can specify the post roll time that will be added to the OUT time for Auto Play On and Auto

Repeat On when Auto Punch In/Out is performed.

When Auto Play On or Auto Repeat On is used in con- junction with Auto Punch In/Out, you will be able to listen for the post roll time after punch out occurs, allowing you to verify the connection following the recording.

1 2

PstRol:00M

P2-1

Post roll time numerical setting

[00...10]

P2-2

Post roll time unit select

[M, s]

Specifies the post roll time in either measures or sec- onds.

In P2-1 you can specify a numerical value (00–10), and in P2-2 you can select either M (measure) or s (second) units. When you change the post roll time unit, the pre roll time unit will change automatically. When M is selected, the maximum post roll time is 10 measures. When s is selected, the maximum is 10 seconds.

When the power is turned on, the pre roll time and post roll time are automatically set to 02M.

Pre roll point

Post roll point

 

 

IN

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pre roll time

 

Post roll time

P3 Program play

Up to 50 songs can be played back in a specified order. Program Play will function only while you are in this page.

When the audio data of each song reaches silence, playback will proceed to the next song.

1 2 3

P01:I-- œ

P3-1Program playback order select

[01...50]

Selects the order (step) of program song playback. The specified song will playback for each step, from low to high numbered steps. Steps for which no song is speci- fied in P3-3 or steps for which the drive specified in P3- 2 and P3-3 was not found will be skipped.

P3-2

Playback drive select

[I, A...G]

 

I: Internal IDE (internal drive), A: SCSI ID 0, B: SCSI ID

 

1, C: SCSI ID 2, D: SCSI ID 3, E: SCSI ID 4, F: SCSI ID 5,

 

G: SCSI ID 6

 

P3-3

Playback song number select

[01...50]

Selects the drive and song number that will playback.

When you exit this page, the selected order of songs will be reset.

The location counter display is different only during Program Play. (Refer to “5. Display MODE”, p.51)

9. TRIGGER

This function allows the beginning of recording to be triggered by the input signal.

Trigger recording on/off

[On, Off]

On (indicator lit): When in record ready mode, an input signal that exceeds the threshold level (refer to EDIT TRIGGER P1) will initiate recording.

Off (indicator off): Recording will begin normally.

Be aware that when this is On, recording will not begin until the threshold level is exceeded. Press the [STOP] key to cancel trigger recording, and readjust the threshold level.

52

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Page Table of Contents Saving to and loading from DAT Adjusting and storing mixer settingsMoving and storing time locations Synchronization and control with a MidiOperation Power on/off Connections, Power-on, DemoConnections to your audio system etc 01Scukyll Turning the power onTurning the power off Listening to the demo songsCreating a new song Naming a songCreating and selecting songs Starting and stopping recording Connecting the input device and adjusting the levelRecording analog record- ing 03KORG1Back Using EQ to modify the tone as you recordAdjusting the EQ Recording digital recordingSaving the effect program Selecting the location at which the effect will be insertedSelecting the effect program Editing the effectMaster Send Type Sending the input sound to the effectApplying the dedicated delay to the input sound Turning the monitor delay on/offEditing the monitor delay Select the playback/recording tracks Select the input monitorMonAuto Storing the in and OUT times Auto Punch In/OutUndo RedoAuto punch in/out setting PstRol02MRehearsing auto punch in/out Combining multiple tracks into one or two tracks Bounce Playback track and recording track settingsApplying EQ and effects while you record Adjusting the playback level and recording levelListening to the metro- nome while you record Playback Trigger recordingApplying an effect to the playback sound Selecting the tracks for playbackSending the playback sound to the external effect Moving the current time Switching scenes dur- ing playbackProgram playback of songs Moving and storing time locationsLocate points LOC1, LOC2, LOC3 Finding a precise time locationMoving to a Mark point Mark pointsStoring a Mark point MarkùM001Enabling parameters for pairing Pairing settingsAdjusting the volume of each channel Pairing on/offAdjusting the High EQ Adjusting the stereo locationUsing the EQ to adjust the tone Adjusting the Effect Send, AUX Send and Track StatusRecalling a scene Switching scenes during a songScene Storing a sceneApplying an effect dur- ing mixdown Recording a master tape MixdownCpyTr 1 ¿ Storing IN, OUT and to timesCopying track data Track Copy EditTrackú¿TrCLP Ï CpyTrCLPÏ¿¿Tr 1x 1Ï Ins¿Tr 1? Inserting a blank space into the track data Insert TrackErasing data from a track Erase Track Inserting a blank space into the IN-OUT area of a trackSwapping the IN-OUT areas of two tracks Deleting data from a track Delete TrackDeleting data from the IN-OUT area of a track Del¿Tr 1?Deleting a song Song RecoverCopying a song Moving a songDeleting a tempo map Tempo map settingsRecording Midi Clock data from a sequencer Creating a tempo mapSelecting the tempo source Recording tap tempoNize a Midi sequencer Using MTC to synchroUsing Midi Clock to synchronize a Midi sequencer to the D8 To the D8DevID 01Ï Using MMC to control the D8 from a Midi sequencerConnecting an external drive RcvMMCo ÏExchanging disks on a removable disk drive Initializing and format- ting a driveSaving a song on a removable disk drive Backup A01SngNa¿ Restore ÏInsNextDsk ARM 100 ¿¿DATokÏ Saving a song to a DAT recorder BackupBackup Ï ¿HDAT100ÏPlayDAT Ï Loading a backed-up song from a DAT recorder RestoreLoading a backed-up song from a DAT recorder Restore HDAT100 ¿Reference Drive/song select SONG/TRACKEdit SONG/TRACK P1 Song number/name displayCpyI1-35ø øB06-40okœ RenamA01œ SngName œDelI01okœ MovøI01okœCpyTr ØTr 1x99œ P3 Edit TrackSystem Input 1/2 assign P2 MIDI/SYNC settingsEdit System Deleting a markDrive information Song backupDiskUtil œ ARM 100 œInitialize/format Song restoreRestore œ ARM 100 ø A01SngN ø ØB02NoDA ØBHD1300œP1 Counter display selection Display ModeREC Mode Play ModeTrigger Edit Play ModeP1 Pre roll time setting P2 Post roll time settingEdit Trigger P1 Threshold level adjustmentP2 Pre trigger time setting P1 Tempo map settingsMetronome P2 Metronome volume settingP1 Tempo source setting Edit Tempo15. IN/LOC1, OUT/LOC2, TO/LOC3 P1 Metronome volume settingP2 Metronome mode setting Edit MetronomeP2 Deleting a scene SceneEdit Scene P1 Scene parameter listP1 Storing IN/LOC 1, OUT/LOC 2, TO/LOC 3 or a Scene StoreScrub UndoTrack Status 22. EQEffect Send Off P2 External output Aux level settingPAN/BALANCE FaderSnd1-2000 P1-1 Pairing on/offPair On/Off REC SelectP1-1Effect program category number select RD1...SE9 Factory Preset, U01...U65 User AreaEffect P1 Effect select200msœ P2 Monitor delay settingsP2-3Monitor delay parameter settings P2-1 Monitor delay on/offAll Effo RenøRoom Edit EffectP1 Editing and saving an effect LoG-15dBœEdit Effect Assign Effect AssignAppendices TroubleshootingMidi sequencer does not synchronize to the D8 Various messages Midi Implementation Chart Block Diagram Effect Assign = Input 1/2 Type EFFECT1 EFFECT2 EFFECT3 EFFECT4 Effect Program List4BEQ 4 Band Equalizer Effect Parameter ListNR Noise Reduction Phono Turntable SIM Moonlit sea written by Yuko Asai Metronome Type ListDemo Song List Scukyll ExpressD8 Specifications Bouncing tracks Functions added to the D8
Top Page Image Contents